tray [ 0.724157] Uniform CD-ROM driver Revision: 3.20 [ 0.724345] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 0.724451] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 0.726887] sda1 sda2 < [ 0.732369] Freeing initrd memory: 12830k freed [ 0.755351] sda5 > [ 0.755956] sd 0:0:0:0: [sda] Attached SCSI disk [ 0.755983] Freeing unused kernel memory: 620k freed [ 0.756366] Write protecting the kernel text: 4540k [ 0.756413] Write protecting the kernel read-only data: 1668k [ 0.769410] usb 1-2: new high speed USB device using ehci_hcd and address 2 [ 0.793088] udev: starting version 151 [ 0.910788] usb 1-2: configuration #1 chosen from 1 choice [ 1.013680] Linux agpgart interface v0.103 [ 1.021574] usb 1-3: new high speed USB device using ehci_hcd and address 3 [ 1.033935] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 1.034016] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.034166] r8169 0000:02:00.0: setting latency timer to 64 [ 1.034213] alloc irq_desc for 26 on node -1 [ 1.034218] alloc kstat_irqs on node -1 [ 1.034236] r8169 0000:02:00.0: irq 26 for MSI/MSI-X [ 1.035497] eth0: RTL8168d/8111d at 0xf8106000, d0:27:88:62:fa:10, XID 083000c0 IRQ 26 [ 1.074831] agpgart-intel 0000:00:00.0: Intel IGD Chipset [ 1.075215] agpgart-intel 0000:00:00.0: detected 8188K stolen memory [ 1.078180] [drm] Initialized drm 1.1.0 20060810 [ 1.086882] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 1.134427] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.134438] i915 0000:00:02.0: setting latency timer to 64 [ 1.143963] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining [ 1.143970] [drm] MTRR allocation failed. Graphics performance may suffer. [ 1.144089] alloc irq_desc for 27 on node -1 [ 1.144094] alloc kstat_irqs on node -1 [ 1.144108] i915 0000:00:02.0: irq 27 for MSI/MSI-X [ 1.144118] [drm] set up 7M of stolen space [ 1.144642] [drm] initialized overlay support [ 1.167226] usb 1-3: configuration #1 chosen from 1 choice [ 1.183707] Initializing USB Mass Storage driver... [ 1.183955] scsi2 : SCSI emulation for USB Mass Storage devices [ 1.184152] usbcore: registered new interface driver usb-storage [ 1.184159] USB Mass Storage support registered. [ 1.184404] usb-storage: device found at 3 [ 1.184408] usb-storage: waiting for device to settle before scanning [ 1.301862] composite sync not supported [ 1.306924] fb0: inteldrmfb frame buffer device [ 1.306930] registered panic notifier [ 1.307023] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 1.311191] vga16fb: initializing [ 1.311198] vga16fb: mapped to 0xc00a0000 [ 1.311206] vga16fb: not registering due to another framebuffer present [ 1.323926] [drm] Big FIFO is enabled [ 1.356037] usb 1-6: new high speed USB device using ehci_hcd and address 4 [ 1.392028] [drm] Big FIFO is enabled [ 1.392046] [drm] Big FIFO is enabled [ 1.392107] [drm] Big FIFO is enabled [ 1.424154] Console: switching to colour frame buffer device 128x48 [ 1.489655] usb 1-6: configuration #1 chosen from 1 choice [ 1.490065] hub 1-6:1.0: USB hub found [ 1.490361] hub 1-6:1.0: 4 ports detected [ 1.641924] [drm] Big FIFO is enabled [ 1.664259] [drm] Big FIFO is enabled [ 1.772743] usb 1-6.1: new high speed USB device using ehci_hcd and address 5 [ 1.805303] composite sync not supported [ 1.865029] usb 1-6.1: configuration #1 chosen from 1 choice [ 1.865603] hub 1-6.1:1.0: USB hub found [ 1.865760] hub 1-6.1:1.0: 4 ports detected [ 1.984632] xor: automatically using best checksumming function: pIII_sse [ 2.004012] pIII_sse : 5564.000 MB/sec [ 2.004016] xor: using function: pIII_sse (5564.000 MB/sec) [ 2.018292] device-mapper: dm-raid45: initialized v0.2594b [ 2.152161] usb 1-6.1.1: new low speed USB device using ehci_hcd and address 6 [ 2.263701] usb 1-6.1.1: configuration #1 chosen from 1 choice [ 2.263944] EXT4-fs (sda1): mounted filesystem with ordered data mode [ 2.298890] usbcore: registered new interface driver hiddev [ 2.301452] input: HID 413c:3010 as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6.1/1-6.1.1/1-6.1.1:1.0/input/input3 [ 2.301658] generic-usb 0003:413C:3010.0001: input,hidraw0: USB HID v1.00 Mouse [HID 413c:3010] on usb-0000:00:1d.7-6.1.1/input0 [ 2.301702] usbcore: registered new interface driver usbhid [ 2.301708] usbhid: v2.6:USB HID core driver [ 2.352678] usb 1-6.1.2: new low speed USB device using ehci_hcd and address 7 [ 2.479348] usb 1-6.1.2: configuration #1 chosen from 1 choice [ 2.489610] input: USB Keyboard as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6.1/1-6.1.2/1-6.1.2:1.0/input/input4 [ 2.489800] generic-usb 0003:04D9:1702.0002: input,hidraw1: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:1d.7-6.1.2/input0 [ 2.506620] input: USB Keyboard as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6.1/1-6.1.2/1-6.1.2:1.1/input/input5 [ 2.506812] generic-usb 0003:04D9:1702.0003: input,hidraw2: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:1d.7-6.1.2/input1 [ 2.592227] usb 1-6.1.3: new full speed USB device using ehci_hcd and address 8 [ 2.807387] usb 1-6.1.3: configuration #1 chosen from 1 choice [ 2.906254] input: Elo TouchSystems, Inc. Elo TouchSystems CarrollTouch 4500U as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6.1/1-6.1.3/1-6.1.3:1.0/input/input6 [ 2.906456] generic-usb 0003:04E7:0030.0004: input,hidraw3: USB HID v1.00 Pointer [Elo TouchSystems, Inc. Elo TouchSystems CarrollTouch 4500U] on usb-0000:00:1d.7-6.1.3/input0 [ 2.992406] usb 1-6.1.4: new high speed USB device using ehci_hcd and address 9 [ 3.102898] usb 1-6.1.4: configuration #1 chosen from 1 choice [ 3.103185] scsi3 : SCSI emulation for USB Mass Storage devices [ 3.103337] usb-storage: device found at 9 [ 3.103343] usb-storage: waiting for device to settle before scanning [ 6.184772] usb-storage: device scan complete [ 6.185413] scsi 2:0:0:0: Direct-Access Generic USB SD Reader PQ: 0 ANSI: 0 [ 6.185913] scsi 2:0:0:1: Direct-Access Generic USB MS Reader PQ: 0 ANSI: 0 [ 6.186961] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 6.187328] sd 2:0:0:1: Attached scsi generic sg3 type 0 [ 6.189017] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 6.189638] sd 2:0:0:1: [sdc] Attached SCSI removable disk [ 8.100226] usb-storage: device scan complete [ 8.101213] scsi 3:0:0:0: Direct-Access Memorex TD Classic 003B PMAP PQ: 0 ANSI: 0 CCS [ 8.102295] sd 3:0:0:0: Attached scsi generic sg4 type 0 [ 8.102812] sd 3:0:0:0: [sdd] 2010112 512-byte logical blocks: (1.02 GB/981 MiB) [ 8.103302] sd 3:0:0:0: [sdd] Write Protect is off [ 8.103309] sd 3:0:0:0: [sdd] Mode Sense: 23 00 00 00 [ 8.103315] sd 3:0:0:0: [sdd] Assuming drive cache: write through [ 8.105425] sd 3:0:0:0: [sdd] Assuming drive cache: write through [ 8.105433] sdd: sdd1 [ 8.108061] sd 3:0:0:0: [sdd] Assuming drive cache: write through [ 8.108069] sd 3:0:0:0: [sdd] Attached SCSI removable disk [ 8.588397] udev: starting version 151 [ 8.703778] Adding 9802744k swap on /dev/sda5. Priority:-1 extents:1 across:9802744k [ 8.938781] lp: driver loaded but no devices found [ 9.064339] parport_pc 00:08: reported by Plug and Play ACPI [ 9.064391] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 9.092509] usbcore: registered new interface driver usblp [ 9.152335] lp0: using parport0 (interrupt-driven). [ 9.195836] ppdev: user-space parallel port driver [ 9.281457] type=1505 audit(1349707961.350:2): operation="profile_load" pid=688 name="/sbin/dhclient3" [ 9.281957] type=1505 audit(1349707961.350:3): operation="profile_load" pid=688 name="/usr/lib/NetworkManager/nm-dhcp-client.action" [ 9.282252] type=1505 audit(1349707961.350:4): operation="profile_load" pid=688 name="/usr/lib/connman/scripts/dhclient-script" [ 9.537114] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.537176] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 9.631529] hda_codec: ALC662 rev1: BIOS auto-probing. [ 9.633436] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input7 [ 9.769512] r8169: eth0: link up [ 9.769523] r8169: eth0: link up [ 9.773302] type=1505 audit(1349707961.842:5): operation="profile_replace" pid=850 name="/sbin/dhclient3" [ 9.773818] type=1505 audit(1349707961.842:6): operation="profile_replace" pid=850 name="/usr/lib/NetworkManager/nm-dhcp-client.action" [ 9.774120] type=1505 audit(1349707961.842:7): operation="profile_replace" pid=850 name="/usr/lib/connman/scripts/dhclient-script" [ 9.775628] type=1505 audit(1349707961.842:8): operation="profile_load" pid=849 name="/usr/share/gdm/guest-session/Xsession" [ 9.799377] type=1505 audit(1349707961.866:9): operation="profile_load" pid=855 name="/usr/lib/cups/backend/cups-pdf" [ 9.800036] type=1505 audit(1349707961.870:10): operation="profile_load" pid=855 name="/usr/sbin/cupsd" [ 9.823185] type=1505 audit(1349707961.890:11): operation="profile_load" pid=851 name="/usr/bin/evince" [ 10.309333] composite sync not supported [ 10.427773] composite sync not supported [ 10.728768] CPU0 attaching NULL sched-domain. [ 10.728779] CPU1 attaching NULL sched-domain. [ 10.748600] CPU0 attaching sched-domain: [ 10.748609] domain 0: span 0-1 level CPU [ 10.748615] groups: 0 1 [ 10.748626] CPU1 attaching sched-domain: [ 10.748630] domain 0: span 0-1 level CPU [ 10.748636] groups: 1 0 [ 10.748992] CPU0 attaching NULL sched-domain. [ 10.749000] CPU1 attaching NULL sched-domain. [ 10.764609] CPU0 attaching sched-domain: [ 10.764617] domain 0: span 0-1 level CPU [ 10.764624] groups: 0 1 [ 10.764635] CPU1 attaching sched-domain: [ 10.764640] domain 0: span 0-1 level CPU [ 10.764645] groups: 1 0 [ 11.441241] composite sync not supported [ 11.578910] composite sync not supported [ 11.692638] composite sync not supported [ 12.472198] CPU0 attaching NULL sched-domain. [ 12.472210] CPU1 attaching NULL sched-domain. [ 12.492398] CPU0 attaching sched-domain: [ 12.492406] domain 0: span 0-1 level CPU [ 12.492413] groups: 0 1 [ 12.492424] CPU1 attaching sched-domain: [ 12.492428] domain 0: span 0-1 level CPU [ 12.492434] groups: 1 0 [ 12.492782] CPU0 attaching NULL sched-domain. [ 12.492790] CPU1 attaching NULL sched-domain. [ 12.516319] CPU0 attaching sched-domain: [ 12.516327] domain 0: span 0-1 level CPU [ 12.516333] groups: 0 1 [ 12.516345] CPU1 attaching sched-domain: [ 12.516349] domain 0: span 0-1 level CPU [ 12.516355] groups: 1 0 [ 19.888019] eth0: no IPv6 routers present [ 20.485910] composite sync not supported [ 20.601282] composite sync not supported [ 20.717242] composite sync not supported [ 26.626371] composite sync not supported [ 28.870693] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 28.921332] ISOFS: changing to secondary root [ 36.283882] I-pipe: Domain RTAI registered. [ 36.283895] RTAI[hal]: <3.8.1> mounted over IPIPE-NOTHREADS 2.6-03. [ 36.283901] RTAI[hal]: compiled with gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) . [ 36.283980] RTAI[hal]: mounted (IPIPE-NOTHREADS, IMMEDIATE (INTERNAL IRQs DISPATCHED), ISOL_CPUS_MASK: 0). [ 36.283984] PIPELINE layers: [ 36.283990] f8a12e20 9ac15d93 RTAI 200 [ 36.283996] c085cb20 0 Linux 100 [ 36.330906] RTAI[malloc]: global heap size = 2097152 bytes, . [ 36.331743] RTAI[sched]: IMMEDIATE, MP, USER/KERNEL SPACE: , kstacks pool size = 524288 bytes. [ 36.331756] RTAI[sched]: hard timer type/freq = APIC/12500388(Hz); default timing: periodic; linear timed lists. [ 36.331764] RTAI[sched]: Linux timer freq = 250 (Hz), TimeBase freq = 1799910000 hz. [ 36.331770] RTAI[sched]: timer setup = 999 ns, resched latency = 2944 ns. [ 36.331901] RTAI[usi]: enabled. [ 36.423712] RTAI[math]: loaded. [ 36.660481] hm2: loading Mesa HostMot2 driver version 0.15 [ 36.666148] hm2_pci: loading Mesa AnyIO HostMot2 driver version 0.7 [ 36.666211] alloc irq_desc for 21 on node -1 [ 36.666216] alloc kstat_irqs on node -1 [ 36.666229] hm2_pci 0000:03:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 36.666236] hm2_pci: discovered 5i23 at 0000:03:00.0 [ 36.666331] hm2_5i23.0: firmware: requesting hm2/5i23/rmsvss6_8.bit [ 36.867964] hm2/hm2_5i23.0: Smart Serial Firmware Version 31 [ 37.000048] hm2/hm2_5i23.0: 72 I/O Pins used: [ 37.000058] hm2/hm2_5i23.0: IO Pin 000 (P2-01): PWMGen #0, pin Not-Enable (Output) [ 37.000066] hm2/hm2_5i23.0: IO Pin 001 (P2-03): Resolver #0, pin NC (Output) [ 37.000072] hm2/hm2_5i23.0: IO Pin 002 (P2-05): Resolver #0, pin SPIDO0 (Input) [ 37.000079] hm2/hm2_5i23.0: IO Pin 003 (P2-07): Resolver #0, pin SPIDO1 (Input) [ 37.000086] hm2/hm2_5i23.0: IO Pin 004 (P2-09): Resolver #0, pin AMUX2 (Output) [ 37.000093] hm2/hm2_5i23.0: IO Pin 005 (P2-11): Resolver #0, pin AMUX1 (Output) [ 37.000100] hm2/hm2_5i23.0: IO Pin 006 (P2-13): Resolver #0, pin AMUX0 (Output) [ 37.000107] hm2/hm2_5i23.0: IO Pin 007 (P2-15): Resolver #0, pin SPICLK (Output) [ 37.000114] hm2/hm2_5i23.0: IO Pin 008 (P2-17): Resolver #0, pin SPICS (Output) [ 37.000121] hm2/hm2_5i23.0: IO Pin 009 (P2-19): Resolver #0, pin REFPDM- (Output) [ 37.000128] hm2/hm2_5i23.0: IO Pin 010 (P2-21): Resolver #0, pin REFPDM+ (Output) [ 37.000135] hm2/hm2_5i23.0: IO Pin 011 (P2-23): PWMGen #0, pin Out0 (PWM or Up) (Output) [ 37.000143] hm2/hm2_5i23.0: IO Pin 012 (P2-25): PWMGen #0, pin Out1 (Dir or Down) (Output) [ 37.000150] hm2/hm2_5i23.0: IO Pin 013 (P2-27): PWMGen #1, pin Out0 (PWM or Up) (Output) [ 37.000158] hm2/hm2_5i23.0: IO Pin 014 (P2-29): PWMGen #1, pin Out1 (Dir or Down) (Output) [ 37.000165] hm2/hm2_5i23.0: IO Pin 015 (P2-31): PWMGen #2, pin Out0 (PWM or Up) (Output) [ 37.000172] hm2/hm2_5i23.0: IO Pin 016 (P2-33): PWMGen #2, pin Out1 (Dir or Down) (Output) [ 37.000180] hm2/hm2_5i23.0: IO Pin 017 (P2-35): PWMGen #3, pin Out0 (PWM or Up) (Output) [ 37.000187] hm2/hm2_5i23.0: IO Pin 018 (P2-37): PWMGen #3, pin Out1 (Dir or Down) (Output) [ 37.000194] hm2/hm2_5i23.0: IO Pin 019 (P2-39): PWMGen #4, pin Out0 (PWM or Up) (Output) [ 37.000202] hm2/hm2_5i23.0: IO Pin 020 (P2-41): PWMGen #4, pin Out1 (Dir or Down) (Output) [ 37.000209] hm2/hm2_5i23.0: IO Pin 021 (P2-43): PWMGen #5, pin Out0 (PWM or Up) (Output) [ 37.000216] hm2/hm2_5i23.0: IO Pin 022 (P2-45): PWMGen #5, pin Out1 (Dir or Down) (Output) [ 37.000224] hm2/hm2_5i23.0: IO Pin 023 (P2-47): PWMGen #0, pin Not-Enable (Output) [ 37.000230] hm2/hm2_5i23.0: IO Pin 024 (P3-01): IOPort [ 37.000236] hm2/hm2_5i23.0: IO Pin 025 (P3-03): IOPort [ 37.000241] hm2/hm2_5i23.0: IO Pin 026 (P3-05): IOPort [ 37.000247] hm2/hm2_5i23.0: IO Pin 027 (P3-07): IOPort [ 37.000252] hm2/hm2_5i23.0: IO Pin 028 (P3-09): IOPort [ 37.000258] hm2/hm2_5i23.0: IO Pin 029 (P3-11): IOPort [ 37.000263] hm2/hm2_5i23.0: IO Pin 030 (P3-13): IOPort [ 37.000269] hm2/hm2_5i23.0: IO Pin 031 (P3-15): IOPort [ 37.000274] hm2/hm2_5i23.0: IO Pin 032 (P3-17): IOPort [ 37.000280] hm2/hm2_5i23.0: IO Pin 033 (P3-19): IOPort [ 37.000286] hm2/hm2_5i23.0: IO Pin 034 (P3-21): IOPort [ 37.000291] hm2/hm2_5i23.0: IO Pin 035 (P3-23): IOPort [ 37.000297] hm2/hm2_5i23.0: IO Pin 036 (P3-25): IOPort [ 37.000302] hm2/hm2_5i23.0: IO Pin 037 (P3-27): IOPort [ 37.000308] hm2/hm2_5i23.0: IO Pin 038 (P3-29): IOPort [ 37.000313] hm2/hm2_5i23.0: IO Pin 039 (P3-31): IOPort [ 37.000319] hm2/hm2_5i23.0: IO Pin 040 (P3-33): IOPort [ 37.000324] hm2/hm2_5i23.0: IO Pin 041 (P3-35): IOPort [ 37.000330] hm2/hm2_5i23.0: IO Pin 042 (P3-37): IOPort [ 37.000336] hm2/hm2_5i23.0: IO Pin 043 (P3-39): IOPort [ 37.000341] hm2/hm2_5i23.0: IO Pin 044 (P3-41): IOPort [ 37.000347] hm2/hm2_5i23.0: IO Pin 045 (P3-43): IOPort [ 37.000352] hm2/hm2_5i23.0: IO Pin 046 (P3-45): IOPort [ 37.000358] hm2/hm2_5i23.0: IO Pin 047 (P3-47): IOPort [ 37.000365] hm2/hm2_5i23.0: IO Pin 048 (P4-01): Smart Serial Interface #0, pin RxData0 (Input) [ 37.000373] hm2/hm2_5i23.0: IO Pin 049 (P4-03): Smart Serial Interface #0, pin RxData1 (Input) [ 37.000379] hm2/hm2_5i23.0: IO Pin 050 (P4-05): IOPort [ 37.000386] hm2/hm2_5i23.0: IO Pin 051 (P4-07): Smart Serial Interface #0, pin RxData3 (Input) [ 37.000393] hm2/hm2_5i23.0: IO Pin 052 (P4-09): Smart Serial Interface #0, pin TxData0 (Output) [ 37.000401] hm2/hm2_5i23.0: IO Pin 053 (P4-11): Smart Serial Interface #0, pin TxEn0 (Output) [ 37.000408] hm2/hm2_5i23.0: IO Pin 054 (P4-13): Smart Serial Interface #0, pin TxData1 (Output) [ 37.000416] hm2/hm2_5i23.0: IO Pin 055 (P4-15): Smart Serial Interface #0, pin TxEn1 (Output) [ 37.000422] hm2/hm2_5i23.0: IO Pin 056 (P4-17): IOPort [ 37.000428] hm2/hm2_5i23.0: IO Pin 057 (P4-19): IOPort [ 37.000435] hm2/hm2_5i23.0: IO Pin 058 (P4-21): Smart Serial Interface #0, pin TxData3 (Output) [ 37.000442] hm2/hm2_5i23.0: IO Pin 059 (P4-23): Smart Serial Interface #0, pin TxEn3 (Output) [ 37.000449] hm2/hm2_5i23.0: IO Pin 060 (P4-25): IOPort [ 37.000454] hm2/hm2_5i23.0: IO Pin 061 (P4-27): IOPort [ 37.000460] hm2/hm2_5i23.0: IO Pin 062 (P4-29): IOPort [ 37.000465] hm2/hm2_5i23.0: IO Pin 063 (P4-31): IOPort [ 37.000471] hm2/hm2_5i23.0: IO Pin 064 (P4-33): IOPort [ 37.000476] hm2/hm2_5i23.0: IO Pin 065 (P4-35): IOPort [ 37.000482] hm2/hm2_5i23.0: IO Pin 066 (P4-37): IOPort [ 37.000488] hm2/hm2_5i23.0: IO Pin 067 (P4-39): IOPort [ 37.000493] hm2/hm2_5i23.0: IO Pin 068 (P4-41): IOPort [ 37.000499] hm2/hm2_5i23.0: IO Pin 069 (P4-43): IOPort [ 37.000504] hm2/hm2_5i23.0: IO Pin 070 (P4-45): IOPort [ 37.000510] hm2/hm2_5i23.0: IO Pin 071 (P4-47): IOPort [ 37.000771] hm2/hm2_5i23.0: registered [ 37.000805] hm2_5i23.0: initialized AnyIO board at 0000:03:00.0 [ 37.050312] classicladder_rt: module license 'LGPL' taints kernel. [ 37.050320] Disabling lock debugging due to kernel taint [ 37.054309] creating ladder-state [ 2111.249561] composite sync not supported [ 3609.868258] composite sync not supported [ 5310.816270] composite sync not supported [ 6725.199990] hm2_5i23.0: dropping AnyIO board at 0000:03:00.0 [ 6725.200003] hm2/hm2_5i23.0: unregistered [ 6725.200040] hm2_pci 0000:03:00.0: PCI INT A disabled [ 6725.200087] hm2_pci: driver unloaded [ 6725.204939] hm2: unloading [ 6725.488757] RTAI[math]: unloaded. [ 6725.557036] SCHED releases registered named ALIEN RTGLBH [ 6725.588443] RTAI[malloc]: unloaded. [ 6725.688028] RTAI[sched]: unloaded (forced hard/soft/hard transitions: traps 0, syscalls 0). [ 6725.692734] I-pipe: Domain RTAI unregistered. [ 6725.692824] RTAI[hal]: unmounted. [ 6748.860446] I-pipe: Domain RTAI registered. [ 6748.860460] RTAI[hal]: <3.8.1> mounted over IPIPE-NOTHREADS 2.6-03. [ 6748.860465] RTAI[hal]: compiled with gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) . [ 6748.860555] RTAI[hal]: mounted (IPIPE-NOTHREADS, IMMEDIATE (INTERNAL IRQs DISPATCHED), ISOL_CPUS_MASK: 0). [ 6748.860560] PIPELINE layers: [ 6748.860565] fae93e20 9ac15d93 RTAI 200 [ 6748.860570] c085cb20 0 Linux 100 [ 6748.906717] RTAI[malloc]: global heap size = 2097152 bytes, . [ 6748.907290] RTAI[sched]: IMMEDIATE, MP, USER/KERNEL SPACE: , kstacks pool size = 524288 bytes. [ 6748.907303] RTAI[sched]: hard timer type/freq = APIC/12500388(Hz); default timing: periodic; linear timed lists. [ 6748.907311] RTAI[sched]: Linux timer freq = 250 (Hz), TimeBase freq = 1799910000 hz. [ 6748.907316] RTAI[sched]: timer setup = 999 ns, resched latency = 2944 ns. [ 6748.907442] RTAI[usi]: enabled. [ 6748.999036] RTAI[math]: loaded. [ 6749.131621] hm2: loading Mesa HostMot2 driver version 0.15 [ 6749.137526] hm2_pci: loading Mesa AnyIO HostMot2 driver version 0.7 [ 6749.137589] hm2_pci 0000:03:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 6749.137596] hm2_pci: discovered 5i23 at 0000:03:00.0 [ 6749.137726] hm2_5i23.0: firmware: requesting hm2/5i23/rmsvss6_8.bit [ 6749.307943] hm2/hm2_5i23.0: Smart Serial Firmware Version 31 [ 6749.439939] hm2/hm2_5i23.0: 72 I/O Pins used: [ 6749.439949] hm2/hm2_5i23.0: IO Pin 000 (P2-01): PWMGen #0, pin Not-Enable (Output) [ 6749.439956] hm2/hm2_5i23.0: IO Pin 001 (P2-03): Resolver #0, pin NC (Output) [ 6749.439963] hm2/hm2_5i23.0: IO Pin 002 (P2-05): Resolver #0, pin SPIDO0 (Input) [ 6749.439970] hm2/hm2_5i23.0: IO Pin 003 (P2-07): Resolver #0, pin SPIDO1 (Input) [ 6749.439977] hm2/hm2_5i23.0: IO Pin 004 (P2-09): Resolver #0, pin AMUX2 (Output) [ 6749.439985] hm2/hm2_5i23.0: IO Pin 005 (P2-11): Resolver #0, pin AMUX1 (Output) [ 6749.439992] hm2/hm2_5i23.0: IO Pin 006 (P2-13): Resolver #0, pin AMUX0 (Output) [ 6749.439999] hm2/hm2_5i23.0: IO Pin 007 (P2-15): Resolver #0, pin SPICLK (Output) [ 6749.440006] hm2/hm2_5i23.0: IO Pin 008 (P2-17): Resolver #0, pin SPICS (Output) [ 6749.440013] hm2/hm2_5i23.0: IO Pin 009 (P2-19): Resolver #0, pin REFPDM- (Output) [ 6749.440020] hm2/hm2_5i23.0: IO Pin 010 (P2-21): Resolver #0, pin REFPDM+ (Output) [ 6749.440027] hm2/hm2_5i23.0: IO Pin 011 (P2-23): PWMGen #0, pin Out0 (PWM or Up) (Output) [ 6749.440035] hm2/hm2_5i23.0: IO Pin 012 (P2-25): PWMGen #0, pin Out1 (Dir or Down) (Output) [ 6749.440042] hm2/hm2_5i23.0: IO Pin 013 (P2-27): PWMGen #1, pin Out0 (PWM or Up) (Output) [ 6749.440050] hm2/hm2_5i23.0: IO Pin 014 (P2-29): PWMGen #1, pin Out1 (Dir or Down) (Output) [ 6749.440057] hm2/hm2_5i23.0: IO Pin 015 (P2-31): PWMGen #2, pin Out0 (PWM or Up) (Output) [ 6749.440065] hm2/hm2_5i23.0: IO Pin 016 (P2-33): PWMGen #2, pin Out1 (Dir or Down) (Output) [ 6749.440072] hm2/hm2_5i23.0: IO Pin 017 (P2-35): PWMGen #3, pin Out0 (PWM or Up) (Output) [ 6749.440080] hm2/hm2_5i23.0: IO Pin 018 (P2-37): PWMGen #3, pin Out1 (Dir or Down) (Output) [ 6749.440087] hm2/hm2_5i23.0: IO Pin 019 (P2-39): PWMGen #4, pin Out0 (PWM or Up) (Output) [ 6749.440095] hm2/hm2_5i23.0: IO Pin 020 (P2-41): PWMGen #4, pin Out1 (Dir or Down) (Output) [ 6749.440102] hm2/hm2_5i23.0: IO Pin 021 (P2-43): PWMGen #5, pin Out0 (PWM or Up) (Output) [ 6749.440110] hm2/hm2_5i23.0: IO Pin 022 (P2-45): PWMGen #5, pin Out1 (Dir or Down) (Output) [ 6749.440117] hm2/hm2_5i23.0: IO Pin 023 (P2-47): PWMGen #0, pin Not-Enable (Output) [ 6749.440123] hm2/hm2_5i23.0: IO Pin 024 (P3-01): IOPort [ 6749.440129] hm2/hm2_5i23.0: IO Pin 025 (P3-03): IOPort [ 6749.440135] hm2/hm2_5i23.0: IO Pin 026 (P3-05): IOPort [ 6749.440141] hm2/hm2_5i23.0: IO Pin 027 (P3-07): IOPort [ 6749.440146] hm2/hm2_5i23.0: IO Pin 028 (P3-09): IOPort [ 6749.440152] hm2/hm2_5i23.0: IO Pin 029 (P3-11): IOPort [ 6749.440158] hm2/hm2_5i23.0: IO Pin 030 (P3-13): IOPort [ 6749.440163] hm2/hm2_5i23.0: IO Pin 031 (P3-15): IOPort [ 6749.440169] hm2/hm2_5i23.0: IO Pin 032 (P3-17): IOPort [ 6749.440175] hm2/hm2_5i23.0: IO Pin 033 (P3-19): IOPort [ 6749.440180] hm2/hm2_5i23.0: IO Pin 034 (P3-21): IOPort [ 6749.440186] hm2/hm2_5i23.0: IO Pin 035 (P3-23): IOPort [ 6749.440192] hm2/hm2_5i23.0: IO Pin 036 (P3-25): IOPort [ 6749.440197] hm2/hm2_5i23.0: IO Pin 037 (P3-27): IOPort [ 6749.440203] hm2/hm2_5i23.0: IO Pin 038 (P3-29): IOPort [ 6749.440235] hm2/hm2_5i23.0: IO Pin 039 (P3-31): IOPort [ 6749.440243] hm2/hm2_5i23.0: IO Pin 040 (P3-33): IOPort [ 6749.440251] hm2/hm2_5i23.0: IO Pin 041 (P3-35): IOPort [ 6749.440258] hm2/hm2_5i23.0: IO Pin 042 (P3-37): IOPort [ 6749.440266] hm2/hm2_5i23.0: IO Pin 043 (P3-39): IOPort [ 6749.440273] hm2/hm2_5i23.0: IO Pin 044 (P3-41): IOPort [ 6749.440281] hm2/hm2_5i23.0: IO Pin 045 (P3-43): IOPort [ 6749.440289] hm2/hm2_5i23.0: IO Pin 046 (P3-45): IOPort [ 6749.440296] hm2/hm2_5i23.0: IO Pin 047 (P3-47): IOPort [ 6749.440305] hm2/hm2_5i23.0: IO Pin 048 (P4-01): Smart Serial Interface #0, pin RxData0 (Input) [ 6749.440315] hm2/hm2_5i23.0: IO Pin 049 (P4-03): Smart Serial Interface #0, pin RxData1 (Input) [ 6749.440323] hm2/hm2_5i23.0: IO Pin 050 (P4-05): IOPort [ 6749.440332] hm2/hm2_5i23.0: IO Pin 051 (P4-07): Smart Serial Interface #0, pin RxData3 (Input) [ 6749.440342] hm2/hm2_5i23.0: IO Pin 052 (P4-09): Smart Serial Interface #0, pin TxData0 (Output) [ 6749.440351] hm2/hm2_5i23.0: IO Pin 053 (P4-11): Smart Serial Interface #0, pin TxEn0 (Output) [ 6749.440361] hm2/hm2_5i23.0: IO Pin 054 (P4-13): Smart Serial Interface #0, pin TxData1 (Output) [ 6749.440370] hm2/hm2_5i23.0: IO Pin 055 (P4-15): Smart Serial Interface #0, pin TxEn1 (Output) [ 6749.440379] hm2/hm2_5i23.0: IO Pin 056 (P4-17): IOPort [ 6749.440386] hm2/hm2_5i23.0: IO Pin 057 (P4-19): IOPort [ 6749.440395] hm2/hm2_5i23.0: IO Pin 058 (P4-21): Smart Serial Interface #0, pin TxData3 (Output) [ 6749.440405] hm2/hm2_5i23.0: IO Pin 059 (P4-23): Smart Serial Interface #0, pin TxEn3 (Output) [ 6749.440413] hm2/hm2_5i23.0: IO Pin 060 (P4-25): IOPort [ 6749.440421] hm2/hm2_5i23.0: IO Pin 061 (P4-27): IOPort [ 6749.440429] hm2/hm2_5i23.0: IO Pin 062 (P4-29): IOPort [ 6749.440437] hm2/hm2_5i23.0: IO Pin 063 (P4-31): IOPort [ 6749.440444] hm2/hm2_5i23.0: IO Pin 064 (P4-33): IOPort [ 6749.440452] hm2/hm2_5i23.0: IO Pin 065 (P4-35): IOPort [ 6749.440459] hm2/hm2_5i23.0: IO Pin 066 (P4-37): IOPort [ 6749.440467] hm2/hm2_5i23.0: IO Pin 067 (P4-39): IOPort [ 6749.440474] hm2/hm2_5i23.0: IO Pin 068 (P4-41): IOPort [ 6749.440482] hm2/hm2_5i23.0: IO Pin 069 (P4-43): IOPort [ 6749.440489] hm2/hm2_5i23.0: IO Pin 070 (P4-45): IOPort [ 6749.440497] hm2/hm2_5i23.0: IO Pin 071 (P4-47): IOPort [ 6749.440761] hm2/hm2_5i23.0: registered [ 6749.440768] hm2_5i23.0: initialized AnyIO board at 0000:03:00.0 [ 6749.472069] creating ladder-state [ 6750.379462] hm2_5i23.0: dropping AnyIO board at 0000:03:00.0 [ 6750.379475] hm2/hm2_5i23.0: unregistered [ 6750.379509] hm2_pci 0000:03:00.0: PCI INT A disabled [ 6750.379555] hm2_pci: driver unloaded [ 6750.384855] hm2: unloading [ 6750.592190] RTAI[math]: unloaded. [ 6750.641718] SCHED releases registered named ALIEN RTGLBH [ 6750.672442] RTAI[malloc]: unloaded. [ 6750.772027] RTAI[sched]: unloaded (forced hard/soft/hard transitions: traps 0, syscalls 0). [ 6750.776596] I-pipe: Domain RTAI unregistered. [ 6750.776685] RTAI[hal]: unmounted. srt@Cinci:~$