[Cutoff] BelongsTo=-1 Climb cut=0 CodeSnip=-1 Comment= Contour method=2 Cut depth=0 Cut direction=0.5 Cutting rules=0 Edge overlap=5 Enabled=0 Feed rate=2000 Finish allowance=0 Grid size=25 ID=-1 Layer= Lead in=-1 Lead in type=0 Lead out=-1 Lead out type=0 Leadins on open paths=0 Length=1 Maximum X size=2000 Maximum Y size=2000 Minimum X size=500 Minimum Y size=500 Name= Offset open paths=0 Optimisation=1 Path rules= Plunge rate=100 Remnants must be rectangular=0 Reverse open paths=0 Start depth=0 Start position=0 Tool=1 Type=RemnantOperation [Cutoff/Custom] [Misc] Count=1 FileVersion=1003 optBias=0.5 Optimisation=2 Template=0 [OpOrder] Op000000=0,3 [Part 0] Angle=0 copyOf=-1 DrawingFile=\\NAS_DRIVE\Data_Work\Data_Work\G_code Jobs\Plasma\Dean two machines\Gantry side plate_nema23\Top bit\Clive_gantrysideplate_nema23-top.dxf enabled=1 HRef=0 Locked=0 name=Clive_gantrysideplate_nema23-top VRef=0 XPos=50 YPos=140.00000000000006 [Part 0/GroupSources] [Part 0/Operation0] Angle threshold=0.9 BelongsTo=-1 CodeSnip=-1 Comment= Contour method=2 Cut depth=0 Cut direction=0.5 Cutting rules=0 Enabled=0 Feed rate=2000 Finish allowance=0 ID=0 Layer=Big circle Lead in=4 Lead in type=0 Lead out=0 Lead out type=0 Leadins on open paths=0 Length=1 Loop corners=0 Loop size=1 Max chain length=0 Minimise thermal distortion=0 Name=No Offset, Big circle, T5: Jet tool Offset open paths=0 Optimisation=1 Overcut=0 Path rules= Plunge rate=100 Reverse cut direction=1 Reverse open paths=0 Start depth=0 Start position=0 Tool=5 Type=JetOperation [Part 0/Operation0/Custom] [Part 0/Operation1] Angle threshold=0.9 BelongsTo=-1 CodeSnip=-1 Comment= Contour method=2 Cut depth=0 Cut direction=0.5 Cutting rules=0 Enabled=0 Feed rate=2000 Finish allowance=0 ID=1 Layer=Big circle Lead in=4 Lead in type=0 Lead out=0 Lead out type=0 Leadins on open paths=0 Length=1 Loop corners=0 Loop size=1 Max chain length=0 Minimise thermal distortion=0 Name=No Offset, Big circle, T7: Centre Spot Offset open paths=0 Optimisation=1 Overcut=0 Path rules= Plunge rate=100 Reverse cut direction=1 Reverse open paths=0 Start depth=0 Start position=0 Tool=7 Type=JetOperation [Part 0/Operation1/Custom] [Part 0/Operation2] Angle threshold=0.9 BelongsTo=-1 CodeSnip=-1 Comment= Contour method=2 Cut depth=0 Cut direction=0.5 Cutting rules=0 Enabled=0 Feed rate=2000 Finish allowance=0 ID=2 Layer=Big circle Lead in=4 Lead in type=0 Lead out=0 Lead out type=0 Leadins on open paths=0 Length=1 Loop corners=0 Loop size=1 Max chain length=0 Minimise thermal distortion=0 Name=No Offset, Big circle, T8: 'Centre Spot' Offset open paths=0 Optimisation=1 Overcut=0 Path rules= Plunge rate=100 Reverse cut direction=1 Reverse open paths=0 Start depth=0 Start position=0 Tool=8 Type=JetOperation [Part 0/Operation2/Custom] [Part 0/Operation3] BelongsTo=-1 Climb cut=0 CodeSnip=-1 Comment= Contour method=2 Coolant=0 Cut depth=1 Cut direction=0.5 Cutting rules=0 Enabled=1 Feed rate=100 Finish allowance=0 ID=3 Layer=Big circle Lead in=-1 Lead in type=0 Lead out=-1 Lead out type=0 Leadins on open paths=0 Length=1 Max hole size=80 Min hole size=2.7 Name=Drill, Big circle, T1: drill, 1 mm Deep Offset open paths=0 Optimisation=1 Path rules= Peck depth=1 Peck retract=1 Plunge rate=100 Reverse open paths=0 Spindle speed=1 Start depth=1 Start position=0 Tool=1 Type=DrillOperation [Part 0/Operation3/Custom] [pathRules] GlobalRule=-1 [Table] MaxHeight=1000 Origin=9 RapidSpeed=2000 tableOrigin=6 TableX1=0 TableX2=1000 TableY1=0 TableY2=1000 ToolTime=0 X1=0 X2=1250 Y1=0 Y2=700 [Tool0] Comment= Depth per pass=1 Diameter=3 Flute length=1 Name=drill Plunge rate=100 Point angle=2.059488517353309 Spindle direction=0 Spindle speed=1 Tool length offset=0 Tool number=1 Type=DrillTool [Tool0/Custom] [Tool1] Comment= Cut height=1.5 Feed rate=2000 Kerf width=0.0001 Name=Jet tool Pause at end of cut=0 Pierce delay=0.5 Pierce height=3 Pierce type=0 Plunge rate=100 Tool number=5 Type=PlasmaTool Wiggle length=10 [Tool1/Custom] [Tool2] Comment= Cut height=1.5 Feed rate=2000 Kerf width=0.0001 Name=Centre Spot Pause at end of cut=0 Pierce delay=0.5 Pierce height=3 Pierce type=0 Plunge rate=100 Tool number=7 Type=PlasmaTool Wiggle length=10 [Tool2/Custom] [Tool3] Comment= Cut height=1.5 Feed rate=2000 Kerf width=0.0001 Name='Centre Spot' Pause at end of cut=0 Pierce delay=0.5 Pierce height=3 Pierce type=0 Plunge rate=100 Tool number=8 Type=PlasmaTool Wiggle length=10 [Tool3/Custom] [ToolChange] BeforeCode= Code= noSafeZ=0 UseX=0 UseY=0 UseZ=0 X=0 Y=0 Z=0 [Variables] [Work] Bottom=0 Clearance=40 isPolygon=0 Notes= Origin=6 ParkUseX=0 ParkUseY=0 ParkUseZ=0 ParkX=0 ParkY=0 ParkZ=0 PlungeSafety=25 polyLayer=0 polyPart=0 Thickness=10 X1=0 X2=100 Y1=0 Y2=280 [Work/keepout] Clamp Clearance Height=RapidClearance Corner 1X=0 Corner 1Y=0 Corner 2X=0 Corner 2Y=0 Function=0 Inside=1 layer=0 part=0 [BinaryDataStart]%dI@a@ Big circle G@Y@!Y;±~Xk\@TNuT+Y@ -DT!? -DT! 𙙙Y3@!Y;±~Xk\@,NuT+2|fff]@DNuT+X@-DT!? -DT! 𙙙Y3@,NuT+2|fff]@L?±~Xk\@ NuT+X@-DT!?  𙙙Y3@L?±~Xk\@'zͼ@Y@NuT+Y@-DT!?  -DT!? 𙙙Y3@'zͼ@Y@L?>NQU@4NuT+Y@-DT!? -DT!? 𙙙Y3@L?>NQU@,NuT+ȃ)T@DNuT+Y@-DT!? !3|@ 𙙙Y3@,NuT+ȃ)T@(Y;@0I@`XGW0F"aD@`-DT! -DT! $@XGW0F"aCaD@`-DT! !3| $@CaD@a1C@`-DT!? DTTTt $@D@aZG@X0F"aD@@`.-DT! -DT! #@ZG@X0F"aI@@`D@@`.-DT! !3|@ #@@ G@Y@#$@ G@Y@#$@ G@Y@#$-NuT+Y@#$