[Cutoff] BelongsTo=-1 Climb cut=0 CodeSnip=-1 Comment= Contour method=2 Cut depth=0 Cut direction=0.5 Cutting rules=0 Edge overlap=5 Enabled=0 Feed rate=2000 Finish allowance=0 Grid size=25 ID=-1 Layer= Lead in=-1 Lead in type=0 Lead out=-1 Lead out type=0 Leadins on open paths=0 Length=1 Maximum X size=2000 Maximum Y size=2000 Minimum X size=500 Minimum Y size=500 Name= Offset open paths=0 Optimisation=1 Path rules= Plunge rate=100 Remnants must be rectangular=0 Reverse open paths=0 Start depth=0 Start position=0 Tool=1 Type=RemnantOperation [Cutoff/Custom] [Misc] Count=1 FileVersion=1003 optBias=0.5 Optimisation=2 Template=0 [OpOrder] Op000000=0,0 [Part 0] Angle=0 copyOf=-1 DrawingFile=Z:\Data_Work\G_code Jobs\Plasma\Dean two machines\Gantry side plate_nema23\gantrysideplate_nema23.DXF enabled=1 HRef=0 Locked=0 name=gantrysideplate_nema23 VRef=0 XPos=50.000000000000028 YPos=140.00000000000003 [Part 0/GroupSources] [Part 0/Operation0] BelongsTo=-1 Climb cut=0 CodeSnip=-1 Comment= Contour method=2 Coolant=0 Cut depth=1 Cut direction=0.5 Cutting rules=0 Enabled=1 Feed rate=100 Finish allowance=0 ID=0 Layer=cirtcle Lead in=-1 Lead in type=0 Lead out=-1 Lead out type=0 Leadins on open paths=0 Length=1 Max hole size=75 Min hole size=2 Name=Drill, cirtcle, T3: Centre Spot, 1 mm Deep Offset open paths=0 Optimisation=1 Path rules= Peck depth=0.001 Peck retract=1 Plunge rate=100 Reverse open paths=0 Spindle speed=0 Start depth=1 Start position=0 Tool=3 Type=DrillOperation [Part 0/Operation0/Custom] [pathRules] GlobalRule=-1 [Table] MaxHeight=1000 Origin=9 RapidSpeed=2000 tableOrigin=6 TableX1=0 TableX2=1000 TableY1=0 TableY2=1000 ToolTime=0 X1=0 X2=1000 Y1=0 Y2=1000 [Tool0] Comment= Cut height=1.5 Feed rate=2000 Kerf width=2.4 Name=Plasma, 2.4 mm kerf Pause at end of cut=0 Pierce delay=0.5 Pierce height=3 Pierce type=0 Plunge rate=100 Tool number=1 Type=PlasmaTool Wiggle length=10 [Tool0/Custom] [Tool1] Comment= Cut height=1.5 Feed rate=2000 Kerf width=1.5 Name=Plasma, 1.5 mm kerf Pause at end of cut=0 Pierce delay=0.5 Pierce height=3 Pierce type=0 Plunge rate=100 Tool number=2 Type=PlasmaTool Wiggle length=10 [Tool1/Custom] [Tool2] Comment= Cut height=1.5 Feed rate=2000 Kerf width=1.5 Name=Centre Spot Pause at end of cut=0 Pierce delay=0.5 Pierce height=3 Pierce type=0 Plunge rate=100 Tool number=3 Type=PlasmaTool Wiggle length=10 [Tool2/Custom] [ToolChange] BeforeCode= Code= noSafeZ=0 UseX=0 UseY=0 UseZ=0 X=0 Y=0 Z=0 [Variables] [Work] Bottom=1 Clearance=40 isPolygon=0 Notes= Origin=6 ParkUseX=1 ParkUseY=1 ParkUseZ=0 ParkX=0 ParkY=0 ParkZ=0 PlungeSafety=25 polyLayer=0 polyPart=0 Thickness=3 X1=0 X2=100 Y1=0 Y2=280 [Work/keepout] Clamp Clearance Height=RapidClearance Corner 1X=0 Corner 1Y=0 Corner 2X=0 Corner 2Y=0 Function=0 Inside=1 layer=0 part=0 [BinaryDataStart]%ëüÿÿÿÿÿHÀ€aÀžcirtcle@ð¿ð¿ÿÿÿÿ4NèuÌT+ÀY@#$