--- QtVCP Screen Started on: Fri, Nov 22 2024 05:01:50 PM ---
--- QtDragon_hd Version 1.5 on Linuxcnc 2.10.0~pre0 ---
17:01:50 Machine OFF
17:01:50 Hard limits tripped
17:01:50 Tool 0: No Tool
17:02:13 Machine ON
17:03:04 Hard limits tripped
17:03:04 Hard limits tripped
17:03:05 Probe tripped during homing motion.
17:03:10 Hard limits tripped
17:03:10 Hard limits tripped
17:03:11 Probe tripped during homing motion.
17:03:13 Hard limits tripped
17:03:13 Hard limits tripped
17:03:38 Hard limits tripped
17:03:39 Hard limits tripped
17:03:41 Hard limits tripped
17:03:41 Hard limits tripped
17:03:45 Hard limits tripped
17:03:46 Hard limits tripped
17:04:00 Cannot switch pages while in AUTO mode
17:04:18 Loaded tool 99
17:04:18 Tool 99: 3D Probe 
17:04:22 Cannot switch pages while in AUTO mode
17:04:26 Versa Probe: Start Cycle: Go to Tool Setter
17:04:36 Versa Probe: Start Cycle: Probe Tool Setter Z Height
17:05:03 HISTORY Tool Setter height Z[-132.873]
17:05:28 Versa Probe: Start Cycle: Probe Z Height of material 
17:05:35 HISTORY Probe Material Top Z[-99.071]
17:06:13 Loaded program file : /home/andy/uploads/Cutting-Board-with-dowels-BOTTOM-FACE-2.ngc
17:06:13 Loaded file /home/andy/uploads/Cutting-Board-with-dowels-BOTTOM-FACE-2.ngc
17:06:22 Started program from line 1
17:06:27  Current Comp Mode: 400.000000
17:06:27  Current Coord System: 540.000000
17:06:27  G43 Tool Offset:  0.000000
17:06:27  Current Selected Tool: 42.000000
17:06:27  Current Selected Pocket: 42.000000
17:06:28  Current Tool Loaded: 99.000000
17:06:28  Current Tool Index:  99.000000
17:08:37 Tool 42: SpeTool Spiral .5" Shank .5" Dia 2" CL 
17:09:01  5063: 249.4924
17:09:01  5070 Probe fail/success: 1.0000
17:09:01  Current Comp Mode: 400.000000
17:09:01  Current Coord System: 540.000000
17:09:01  G43 Tool Offset:  0.000000
17:09:01  Current Selected Tool: 42.000000
17:09:01  Current Selected Pocket: 42.000000
17:09:01  Current Tool Loaded: 99.000000
17:09:01  Current Tool Index:  99.000000
17:09:04 Run timer stopped at 00:02:41
17:09:04 Tool 42: SpeTool Spiral .5" Shank .5" Dia 2" CL 
17:09:04  5063: 249.6038
17:09:04  5070 Probe fail/success: 1.0000
17:09:04  Current Comp Mode: 400.000000
17:09:04  Current Coord System: 540.000000
17:09:04  G43 Tool Offset:  0.000000
17:09:04  Current Selected Tool: 42.000000
17:09:04  Current Selected Pocket: 42.000000
17:09:04  Current Tool Loaded: 99.000000
17:09:05  Current Tool Index:  99.000000
17:09:05  Current Tool Z Offset: 283.402840
17:09:05  Probe Height: -132.8700
17:09:05  Block Height: -99.0710
17:09:05  Probe Result: 249.6038
17:09:05  5063        : 249.6038
17:09:05  Calculated Offset: 283.4028
17:09:05  5070 Probe fail/success: 1.0000
17:09:05  Current Comp Mode: 400.000000
17:09:05  Current Coord System: 540.000000
17:09:06  G43 Tool Offset:  0.000000
17:09:06  Current Selected Tool: 42.000000
17:09:06  Current Selected Pocket: 42.000000
17:09:06  Current Tool Loaded: 99.000000
17:09:06  Current Tool Index:  99.000000
17:09:06  Return to original tool-tip position using new z-offset: 1.764000 , 2.107527 , 369.071000
17:09:06 Linear move on line 290 would exceed Z's positive limit
17:09:06 Linear move on line 290 would exceed joint 3's positive limit
17:09:06 invalid params in linear command
17:09:06 Abort Parameter is [3]