-- *****************************************************************************
-- * USER OPTIONS: change to suit                                              *
-- *                                                                           *
-- * cParms & pmx485 show custom PlasmaC parameters in the SheetCam tool file. *
-- * SheetCam does not use them but they are read by PlasmaCs materialverter   *
-- * to import parameters into the PlasmaC material file from a SheetCam       *
-- *  toolset file.                                                            *
-- *                                                                           *
-- * The PlasmaC GCode parser will remove line numbers so they don't show in   *
-- * in the GUI but if enabled here they will appear in any GCode file saved   *
-- * from SheetCam.                                                            *
-- *****************************************************************************

cParms      = 0 -- set to 1 to show basic custom parameters
pmx485      = 0 -- set to 1 to show RS485 parameters
lineNumbers = 0 -- set to 1 to show linenumbers
noArcs      = 0 -- set to 1 to convert arcs to line segments
matPrompt   = 0 -- set to 1 to bypass material prompt for material #0

-- *** DO NOT CHANGE ANYTHING BELOW THIS LINE **********************************

revNum  = '8'
revDate = 'Dec 23 2021'

if cParms == 1 then
    post.DefineCustomToolParam('PlasmaTool', 'Puddle jump height', 'pjHeight', sc.unit1DECPLACE, 0, 0, 200)
    post.DefineCustomToolParam('PlasmaTool', 'Puddle jump delay', 'pjDelay', sc.unit2DECPLACE, 0, 0, 9)
    post.DefineCustomToolParam('PlasmaTool', 'THC enable', 'thcEnable', sc.unitBOOLEAN, 1, 0, 1)
    post.DefineCustomToolParam('PlasmaTool', 'Cut voltage', 'cutVolts', sc.unit0DECPLACE, 99, 0, 200)
end

if pmx485 == 1 then
        post.DefineCustomToolParam('PlasmaTool', 'Cut current', 'cutAmps', sc.unit0DECPLACE, 45, 10, 200)
        post.DefineCustomToolParam('PlasmaTool', 'Gas pressure', 'gasPressure', sc.unit0DECPLACE, 0, 0, 150)
        post.DefineCustomToolParam('PlasmaTool', 'Cut mode', 'cutMode', sc.unit0DECPLACE, 1, 1, 3)
end

function OnAbout(event)
    ctrl = event:GetTextCtrl()
    ctrl:AppendText('For a PlasmaC configuration on LinuxCNC\n\n')
    ctrl:AppendText('Revision: ' .. revNum .. ' - ' .. revDate .. '\n')
end

function OnInit()
    post.SetCommentChars ('()', '[]')  --ensure ( ) characters do not appear in system text
    post.Text (';     file name: ', fileName, '\n')
    post.Text ('; date and time: ', os.date('%a') , ' ', os.date('%b') , ' ', os.date('%d') , ' ', os.date('%Y') , '    ', time, '\n')
    post.Text ('; postprocessor: ', postName, ' rev: ', revNum, '\n')
    post.Text (';\n')
    post.Text (';begin pre-amble\n')

    if scale == metric then
        minimumMove = '0.000001'
        post.Text (' G21 (units: metric)\n') --metric mode
        units = 'mm'
        precision = '0.000'
    else
        post.Text (' G20 (units: inches)\n') --inch mode
        minimumMove = '0.00000004'
        units = '"'
        precision = '0.00000'
    end
    post.Text (' G40 (cutter compensation: off)\n')
    post.Text (' G90 (distance mode: absolute)\n')
    post.Text (' M52 P1 (adaptive feed: on)\n') 
    post.Text (' M65 P2 (enable THC)\n')
    post.Text (' M65 P3 (enable torch)\n')
    post.Text (' M68 E3 Q0 (velocity 100%)\n')
    if scale == metric then
        post.Text (' G64 P0.254 Q0.025 (tracking tolerances: 0.254mm)\n') 
    else
        post.Text (' G64 P0.01 Q0.001 (tracking tolerances: 0.01")\n') 
    end
    post.Text (' F#<_hal[plasmac.cut-feed-rate]>\n')
    post.Text (';end pre-amble\n')
    post.Text (';\n')
    bigArcs = 1 --stitch arc segments together
    minArcSize = 0.2 --arcs smaller than this are converted to moves
    cut = 1
    cutLength = 0
    cutType = 'Cutting'
    cutName = 'cut'
    pierces = 0
    spots = 0
    scribes = 0
    scribeLength = 0
    oldTool = 0
    drilling = 0
end

function OnNewLine()
    if lineNumbers == 1 then
        post.Text ('N')
        post.Number (lineNumber, '00000')
        post.Text (' ')
        lineNumber = lineNumber + 10
    end
end

function OnComment()
    post.Text('(',commentText,')\n')
end

function OnToolChange()
    post.Text (';begin material setup\n')
    if string.match (toolName, 'Air Scribe') or 
       string.match (toolName, 'Engraver') or 
       string.match(toolClass, 'MarkerTool') then
        cutType = 'Scribing'
        cutName = 'scribe'
        spindleNum = 1
        toolNum = 1
    elseif string.match (toolName, 'Centre Spot') or
           string.match (toolName, 'Center Spot') or
           string.match(operationClass, 'DrillOperation') then
        cutType = 'Spotting'
        cutName = 'spot'
        spindleNum = 2
        toolNum = 0
    else
        cutType = 'Cutting'
        cutName = 'cut'
        spindleNum = 0
        toolNum = 0
    end
    if toolNum ~= oldTool then
        post.Text (' T', toolNum, ' M6 (select ', string.lower(cutType), ' tool)\n')
        post.Text (' G43 H0 (apply tool offsets)\n')
        post.Text (';\n')
        oldTool = toolNum
    end
    if tool == 0 and matPrompt == 0 then
        post.Text ('; Use manually selected tool\n')
        post.Text ('(msg,Ensure correct material is selected then press RESUME to continue)\n')
        post.Text (' M1\n')
    else
        post.Text (' M190 P' , tool,' (',string.lower(toolName), ' material)\n')            
        post.Text (' M66 P3 L3 Q2 (wait for valid change)\n')            
    end
    post.Text (' F#<_hal[plasmac.cut-feed-rate]>\n')
    post.Text (';end material setup\n')
end

function OnPenDown()
    post.Text ('\n M3 $', spindleNum, ' S1 (', cutName, ' start)\n')
    if cutType == 'Scribing' then
        scribeLength = scribeLength + (entityLength * scale)
        scribes = scribes + 1
    elseif cutType == 'Spotting' then
        post.Text (' G91 (relative distance mode)\n')
        post.Text (' G1 X', minimumMove, ' (tiny move)\n')
        post.Text (' G90 (absolute distance mode)\n')
        spots = spots + 1
    else
        cutLength = cutLength + (entityLength * scale)
        pierces = pierces + 1
    end
    entityLength = 0
end

function OnPenUp()
    post.Text ('\n M5 $', spindleNum, '(', cutName, ' stop)\n')
    if string.match (toolName, 'Air Scribe') then
        post.Text (' G4 P1 (pause for scribe retract)\n')
    end
    post.Text (';end ', string.lower(partName), ', ',string.lower(cutType), ' #', cut, '\n')
    cut = cut + 1
end

function OnRapid()
    if math.hypot(endX - currentX, endY - currentY) < tonumber(minimumMove) then
        return
    end
    if (entityLength and entityLength >= tonumber(minimumMove)) or drilling == 1 then
        post.Text (';\n;begin ', string.lower(partName), ' #', cut, ', ',string.lower(cutType))
        if cutType == 'Cutting' or cutType == 'Scribing' then
            post.Text (', ')
            post.Number (entityLength * scale, '0.00')
            post.Text (units)
        end
    else
        post.Text (';\n;park torch\n')
    end
    post.Text ('\n')
    post.ModalText('')
    post.ModalText (' G0')
    post.NonModalNumber (' X', endX * scale, precision)
    post.NonModalNumber (' Y', endY * scale, precision)
    post.Text ('\n')
end

function OnMove()
    if cutType == 'Cutting'  or cutType == 'Scribing' then
        if math.hypot(endX - currentX, endY - currentY) < tonumber(minimumMove) then
            return
        end
        post.ModalText('')
        post.ModalText (' G1')
        post.NonModalNumber (' X', endX * scale, precision)
        post.NonModalNumber (' Y', endY * scale, precision)
        post.Text ('\n')
    end
end

function OnArc()
    if cutType == 'Cutting' or cutType == 'Scribing' then
        if noArcs == 1 then
            post.ArcAsMoves(0.25)
        else
            post.ModalText('')
            if(arcAngle < 0) then
                post.ModalText (' G3')
            else
                post.ModalText (' G2')
            end
            post.NonModalNumber (' X', endX * scale, precision)
            post.NonModalNumber (' Y', endY * scale, precision)
            post.Text (' I')
            post.Number ((arcCentreX - currentX) * scale, precision)
            post.Text (' J')
            post.Number ((arcCentreY - currentY) * scale, precision)
            post.Text ('\n')
        end
    end
end

function OnDrill()
    if cutType == 'Spotting' then
        drilling = 1
        OnRapid()
        OnPenDown()
        OnPenUp()
        drilling = 0
    end
end

function OnFinish()
    post.Text (';\n;begin post-amble\n')
    if toolNum > 0 then
        post.Text (' T0 M6 (select torch)\n')
        post.Text (' G43 H0 (apply tool offsets)\n')
        if cutType == 'Scribing' then
            post.Text (' M65 P0\n')
        end
    end
    post.Text (' G40 (cutter compensation: off)\n')
    post.Text (' G90 (distance mode: absolute)\n')
    post.Text (' M65 P2 (enable THC)\n')
    post.Text (' M65 P3 (enable torch)\n')
    post.Text (' M68 E3 Q0 (velocity 100%)\n')
    post.Text (' M5 $-1 (backup stop)\n')
    post.Text (';end post-amble\n')
    post.Text (';\n')
    post.Text (';begin statistics\n')
    if spots > 0 then
        post.Text('\n;  Spots = ', spots, '\n')
    end
    if pierces > 0 then
        post.Text('\n;Pierces = ', pierces, '\n')
    end
    if cutType == 'Cutting' then
        post.Text('\n;   Cuts = ', pierces , ',    Length = ')
        post.Number (cutLength, '0.00')
        post.Text (units, '\n')
    end
    if scribes > 0 then
        post.Text('\n;Scribes = ', scribes , ',    Length = ')
        post.Number (scribeLength, '0.00')
        post.Text (units, '\n')
    end
    post.Text (';end statistics\n')
    post.Text (';\n')
    post.Text (' M30 (end program)\n')
end