ESC in axis 2.9.0 is that a proper behaviour

More
05 Mar 2022 16:10 #236439 by radom
I have a question,
lets say I have a lathe and executing code/mdi command, spindle is running and I press ESC - everything stops ok, I click touch off, enter number and then spindle turns on by itself
which I think is not ideal
2.8.2 didn't do that
is that a intended change or a bug or a mistake in my config
 

Please Log in or Create an account to join the conversation.

More
05 Mar 2022 20:35 #236451 by cmorley
That is a bug.
The following user(s) said Thank You: radom

Please Log in or Create an account to join the conversation.

More
10 Mar 2022 00:01 #236796 by andypugh
Can you report this as a bug on the bug tracker?

github.com/LinuxCNC/linuxcnc/issues

Please Log in or Create an account to join the conversation.

More
13 Mar 2022 11:43 #237102 by radom
I don't know what that was,
I can't reproduce it anymore
If I figure it out I will report it as a bug
thanks

Please Log in or Create an account to join the conversation.

More
15 Mar 2022 17:07 #237346 by andypugh
I would guess that this is related to touching-off diameter when in constant surface speed mode.

Please Log in or Create an account to join the conversation.

More
29 Mar 2022 17:53 - 29 Mar 2022 17:54 #238632 by radom

I would guess that this is related to touching-off diameter when in constant surface speed mode.

 
I don't know what is happening
I mostly use 2.8.2 but when I open 2.9.0 one day the "bug" is present and another day I cannot reproduce it
and I'm doing the same thing after opening axis, mdi - m3 - esc - touch off
if it works it works with both g96 or g97 doesnt matter


 

Last edit: 29 Mar 2022 17:54 by radom.

Please Log in or Create an account to join the conversation.

More
30 May 2022 16:37 #244226 by radom
Ok something different but similar
could someone reproduce this in 2.9.0 axis:
MDI - M3 s100 - spindle starts
press ESC - spindle stops, I can see M5 in Active g-codes in axis
mdi S50 enter - spindle starts

Please Log in or Create an account to join the conversation.

More
31 May 2022 23:39 #244322 by andypugh

Ok something different but similar
could someone reproduce this in 2.9.0 axis:
MDI - M3 s100 - spindle starts
press ESC - spindle stops, I can see M5 in Active g-codes in axis
mdi S50 enter - spindle starts


Yes, I see the same thing with 2.9. 

Oddly, not with 2.8. Which is a bit unexpected as if there was a bug in spindle handling I would have expected it to be related to the multispindle changes, but those are in 2.8 too. 
 

Please Log in or Create an account to join the conversation.

More
31 May 2022 23:40 #244323 by andypugh
Are you building LinuxCNC from source, or using packages?
(If from source, do you have the time to do a git bisect to find when the issue was introduced?)

Please Log in or Create an account to join the conversation.

More
01 Jun 2022 01:12 #244333 by cmorley
I bet this is my code. I changed the spindle to change state on m3/4/5 rather then on s=0/s!=0.
I probably didn't look at abort, which probably stops the spindle by settting S to 0 but not M to 5.

Do you know where the abort code lives - I will take a look.

Please Log in or Create an account to join the conversation.

Time to create page: 0.711 seconds
Powered by Kunena Forum