Recent Topics (231 topics)

Subject	Replies / Views	Last Post

Schaublin 125-CNC retrofit. Category: Turning Topic started 21 Feb 2021 12:38, by RotarySMP Last Post 26 Mar 2026 17:42 by spumco 1 2 3 ... 65	Replies:644 Views:185k	spumco Last Post by spumco 26 Mar 2026 17:42
Toolchanger HAL Component project Category: HAL Examples Topic started 03 Jan 2023 18:14, by smc.collins Last Post 26 Mar 2026 17:10 by RotarySMP 1 2 3	Replies:27 Views:9343	Last Post by RotarySMP 26 Mar 2026 17:10
Qtplasmac- adding .py files as user buttons Category: General LinuxCNC Questions Topic started 26 Mar 2026 15:22, by Nathan40 Last Post 26 Mar 2026 16:24 by Nathan40	Replies:2 Views:57	Nathan40 Last Post by Nathan40 26 Mar 2026 16:24
Stepperonline A6 400W Servo RS485 Step/Dir (ohne EtherCAT) Category: Deutsch Topic started 26 Mar 2026 14:41, by MiMaMoadlo Last Post 26 Mar 2026 15:52 by meister	Replies:1 Views:37	meister Last Post by meister 26 Mar 2026 15:52
Leave enabled pin active when leaving linuxcnc Category: Basic Configuration Topic started 26 Mar 2026 11:29, by mooser Last Post 26 Mar 2026 15:30 by tommylight	Replies:6 Views:103	Last Post by tommylight 26 Mar 2026 15:30
xhc-hb04 does not communicate Category: General LinuxCNC Questions Topic started 13 Mar 2026 12:19, by billykid Last Post 26 Mar 2026 12:45 by billykid	Replies:2 Views:217	Last Post by billykid 26 Mar 2026 12:45
Ethercat Setup help needed for beginner Category: EtherCAT Topic started 26 Mar 2026 12:40, by Spezidrohne Last Post 26 Mar 2026 12:40 by Spezidrohne	Replies:0 Views:54	Spezidrohne Last Post by Spezidrohne 26 Mar 2026 12:40
Review Request for Arc Volt Sensor Schematic Category: Plasma & Laser Topic started 25 Mar 2026 09:58, by alangibson Last Post 26 Mar 2026 12:39 by alangibson	Replies:8 Views:179	alangibson Last Post by alangibson 26 Mar 2026 12:39
Probe tripped during non-probe move deadlock Category: General LinuxCNC Questions Topic started 26 Jul 2025 03:30, by AkkiSan Last Post 26 Mar 2026 12:08 by abs32 1 2 3 4	Replies:31 Views:2973	abs32 Last Post by abs32 26 Mar 2026 12:08
Issue with G38.5 Category: General LinuxCNC Questions Topic started 20 Oct 2025 17:21, by christer Last Post 26 Mar 2026 12:06 by abs32 1 2	Replies:11 Views:1524	abs32 Last Post by abs32 26 Mar 2026 12:06
too long hm2_7i97.0.read.tmax or something else? Category: Driver Boards Topic started 25 Mar 2026 11:32, by m0602232 Last Post 26 Mar 2026 11:56 by rodw 1 2	Replies:11 Views:227	Last Post by rodw 26 Mar 2026 11:56
THC not getting active even when "all seemingly needed" requirements are met Category: Plasmac Topic started 23 Mar 2026 19:05, by AntonioT Last Post 26 Mar 2026 09:30 by rodw	Replies:6 Views:261	Last Post by rodw 26 Mar 2026 09:30
Where is discussion for my new comp Category: General LinuxCNC Questions Topic started 26 Mar 2026 07:42, by tom3p Last Post 26 Mar 2026 09:17 by Aciera	Replies:2 Views:82	Last Post by Aciera 26 Mar 2026 09:17
El5101 Config Category: EtherCAT Topic started 06 Mar 2026 20:58, by rock861261 Last Post 26 Mar 2026 07:50 by Hakan 1 2	Replies:16 Views:803	Hakan Last Post by Hakan 26 Mar 2026 07:50
Integrating a BCL-AMP capacitive sensor to LinuxCNC Category: Plasma & Laser Topic started 02 Feb 2024 01:41, by shasse Last Post 26 Mar 2026 03:55 by Nathan40 1 2 3 ... 6	Replies:52 Views:13.5k	Nathan40 Last Post by Nathan40 26 Mar 2026 03:55
Closed loop - encoder/position not updating while moving Category: HAL Topic started 23 Mar 2026 10:19, by backyardengineer Last Post 25 Mar 2026 23:51 by tommylight	Replies:8 Views:249	Last Post by tommylight 25 Mar 2026 23:51
probe basic lath to define a net spindle-index-en spindle.0.index-enable Category: HAL Topic started 25 Mar 2026 23:09, by leexi Last Post 25 Mar 2026 23:09 by leexi	Replies:0 Views:48	leexi Last Post by leexi 25 Mar 2026 23:09
Struggling with LinuxCNC RPi distro, Remora, NVME V5 Category: Driver Boards Topic started 17 Mar 2026 10:24, by madmetal Last Post 25 Mar 2026 23:03 by scotta	Replies:1 Views:132	Last Post by scotta 25 Mar 2026 23:03
Connect Spindel with 7i96s Category: General LinuxCNC Questions Topic started 25 Mar 2026 20:25, by Tach0 Last Post 25 Mar 2026 21:24 by PCW	Replies:1 Views:84	Last Post by PCW 25 Mar 2026 21:24
Mitsubishi Meldas Control and Motors Category: Milling Machines Topic started 04 Mar 2025 08:58, by gmr Last Post 25 Mar 2026 21:10 by dm17ry	Replies:7 Views:1310	Last Post by dm17ry 25 Mar 2026 21:10