General LinuxCNC Questions 5893 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Mesa 7i92 using pins for GPIO Topic started 16 Aug 2016 06:34, by dannym Last Post 26 Aug 2016 00:49 by dannym	Replies:4 Views:2719	dannym Last Post by dannym 26 Aug 2016 00:49
Lathe with C axis (almost done, need some help) Topic started 23 Aug 2016 20:34, by emcPT Last Post 24 Aug 2016 18:15 by andypugh	Replies:5 Views:3796	Last Post by andypugh 24 Aug 2016 18:15
Spindle speed calibration Topic started 16 Aug 2016 17:09, by bill.anderson Last Post 23 Aug 2016 15:32 by andypugh 1 2	Replies:11 Views:4883	Last Post by andypugh 23 Aug 2016 15:32
Watchdog detected hard LOCKUP on cpu 1 Topic started 10 Aug 2016 15:00, by Cpk_Rbt Last Post 23 Aug 2016 12:37 by Todd Zuercher	Replies:2 Views:1916	Last Post by Todd Zuercher 23 Aug 2016 12:37
Urgent help required with EMC please Topic started 11 Aug 2016 09:35, by sxyuklad Last Post 21 Aug 2016 23:39 by andypugh 1 2 3 ... 13	Replies:128 Views:19k	Last Post by andypugh 21 Aug 2016 23:39
cut and paste from HAL configuration Topic started 09 Aug 2016 22:09, by jwsigler Last Post 20 Aug 2016 17:22 by BigJohnT	Replies:5 Views:2224	Last Post by BigJohnT 20 Aug 2016 17:22
Stepper Sizing Topic started 09 Aug 2016 22:19, by Robotwizard Last Post 19 Aug 2016 17:31 by andypugh	Replies:4 Views:1506	Last Post by andypugh 19 Aug 2016 17:31
Kinematics problem Topic started 18 Aug 2016 10:07, by bodhi_94 Last Post 19 Aug 2016 03:28 by Todd Zuercher	Replies:3 Views:1119	Last Post by Todd Zuercher 19 Aug 2016 03:28
SOLVED: (Me) Why G55G90G0X-6.88 ends at X-19.15?? Topic started 18 Aug 2016 03:29, by clunc Last Post 18 Aug 2016 22:14 by tommylight	Replies:4 Views:3013	Last Post by tommylight 18 Aug 2016 22:14
Foam XYUV feed rate issue on UV axis Topic started 07 Aug 2016 15:34, by delinq Last Post 15 Aug 2016 12:06 by andypugh	Replies:9 Views:1696	Last Post by andypugh 15 Aug 2016 12:06
Encoder counts for Spindle Topic started 14 Aug 2016 16:42, by sspeed33317 Last Post 14 Aug 2016 20:10 by PCW	Replies:1 Views:1230	Last Post by PCW 14 Aug 2016 20:10
Debian Wheezy Topic started 07 Aug 2016 21:04, by thor44 Last Post 13 Aug 2016 21:08 by BigJohnT	Replies:4 Views:1350	Last Post by BigJohnT 13 Aug 2016 21:08
Mesa 7i77 output voltages Topic started 11 Aug 2016 23:16, by jwsigler Last Post 13 Aug 2016 17:38 by jwsigler 1 2	Replies:12 Views:6063	jwsigler Last Post by jwsigler 13 Aug 2016 17:38
install hangs at "Detect network hardware" Topic started 11 Aug 2016 20:15, by BikeCourse Last Post 12 Aug 2016 17:36 by cncnoob1979	Replies:2 Views:2232	Last Post by cncnoob1979 12 Aug 2016 17:36
6I25 + 7I25 mode selection questions Topic started 05 Aug 2016 11:04, by G21 Last Post 11 Aug 2016 23:44 by G21	Replies:5 Views:1284	G21 Last Post by G21 11 Aug 2016 23:44
Simple HAL logical test Topic started 11 Aug 2016 17:20, by jwsigler Last Post 11 Aug 2016 17:54 by jwsigler	Replies:2 Views:1199	jwsigler Last Post by jwsigler 11 Aug 2016 17:54
Kinematics problem Topic started 04 Aug 2016 11:16, by bodhi_94 Last Post 11 Aug 2016 05:28 by bodhi_94	Replies:2 Views:1438	Last Post by bodhi_94 11 Aug 2016 05:28
round holes not exactly round, slight oval shape Topic started 10 Aug 2016 17:34, by bschiett Last Post 10 Aug 2016 18:54 by Todd Zuercher	Replies:1 Views:2849	Last Post by Todd Zuercher 10 Aug 2016 18:54
Simodrive 611 -> LinuxCNC Topic started 09 May 2016 07:09, by emcPT Last Post 09 Aug 2016 19:58 by emcPT	Replies:3 Views:2393	Last Post by emcPT 09 Aug 2016 19:58
Simple GUI plugin for milling pockets, etc. Topic started 07 Aug 2016 21:42, by Transistor Last Post 08 Aug 2016 21:08 by Transistor	Replies:2 Views:2074	Last Post by Transistor 08 Aug 2016 21:08

Time to create page: 0.378 seconds