Ethernet connection to Mesa 7i76e disconnecting on its own after one minute

  • RMJ fabrication
  • Topic Author
  • Offline
  • Senior Member
  • Senior Member
More
5 months 1 week ago #346620 by RMJ fabrication
Ethernet connection to Mesa 7i76e disconnecting on its own after one minute was created by RMJ fabrication
  I ran pnconf wizard and made a configuration for my CNC plasma table. I am able to home and jog my machine for about a minute until I get this error. 
It seems like the ethernet connection is disconnecting on its own somehow. Any ideas on how I could get the ethernet to stay connected so I can use my machine.

Please Log in or Create an account to join the conversation.

More
5 months 1 week ago - 5 months 1 week ago #346622 by PCW
Replied by PCW on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
Is this possibly Plasma/EMI related?

That is, do you still get communication loss when the Plasma source is off?
Last edit: 5 months 1 week ago by PCW.

Please Log in or Create an account to join the conversation.

  • RMJ fabrication
  • Topic Author
  • Offline
  • Senior Member
  • Senior Member
More
5 months 1 week ago #346625 by RMJ fabrication
Replied by RMJ fabrication on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
I don’t think it is Plasma/EMI related. My plasma cutter was not connected or turned on.

Please Log in or Create an account to join the conversation.

More
5 months 1 week ago #346630 by PCW
Replied by PCW on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
What does:

sudo chrt 99 ping -i .001 -q -c 60000 [card_ip_address]

report? (it will run 1 minute then print statistics)

[card_ip_address] is either 10.10.10.10 or 192.168.1.121 depending on 7I76e jumpering

Please Log in or Create an account to join the conversation.

  • RMJ fabrication
  • Topic Author
  • Offline
  • Senior Member
  • Senior Member
More
5 months 1 week ago #346632 by RMJ fabrication
Replied by RMJ fabrication on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
 

Please Log in or Create an account to join the conversation.

More
5 months 1 week ago #346636 by PCW
Replied by PCW on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
Sounds like host or 7I76E issues

Whats does

ip a

report?
 

Please Log in or Create an account to join the conversation.

  • RMJ fabrication
  • Topic Author
  • Offline
  • Senior Member
  • Senior Member
More
5 months 1 week ago #346638 by RMJ fabrication
Replied by RMJ fabrication on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
 

Please Log in or Create an account to join the conversation.

  • tommylight
  • Away
  • Moderator
  • Moderator
More
5 months 1 week ago #346641 by tommylight
Replied by tommylight on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
Did you try another LAN cable?
Is the machine and the PC grounded properly?
Use a DVM and measure between Mesa 24V GND and machine case, in AC mode, while the machine is ON, post result.
www.youtube.com/@toma.cnc1
www.youtube.com/@toma.3d
www.youtube.com/@tomapc

Please Log in or Create an account to join the conversation.

  • RMJ fabrication
  • Topic Author
  • Offline
  • Senior Member
  • Senior Member
More
5 months 1 week ago #346642 by RMJ fabrication
Replied by RMJ fabrication on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
I did not try another LAN cable.
The machine and PC are grounded properly.
I dont have a DVM at the moment but as soon as I get one I will measure those.
I believe this is a software issue because even with qtplasmac not running I get the disconnected error every 45 seconds
 

Please Log in or Create an account to join the conversation.

  • tommylight
  • Away
  • Moderator
  • Moderator
More
5 months 1 week ago #346644 by tommylight
Replied by tommylight on topic Ethernet connection to Mesa 7i76e disconnecting on its own after one minute
Can you power off the machine and leave only Mesa powered?
www.youtube.com/@toma.cnc1
www.youtube.com/@toma.3d
www.youtube.com/@tomapc

Please Log in or Create an account to join the conversation.

Moderators: snowgoer540
Time to create page: 0.081 seconds
Powered by Kunena Forum