PiDiCNC Control System
- andypugh
-
- Offline
- Moderator
-
Less
More
- Posts: 19677
- Thank you received: 4553
20 Nov 2017 16:53 #102068
by andypugh
LinuxCNC is built and tested on ARM but AFAIK only on armhf.
You can see all the platforms that the buildbot test-compiles for here:
buildbot.linuxcnc.org/buildbot/waterfall
If using Jessie, there are even packages: buildbot.linuxcnc.org/dists/jessie/maste...reempt/binary-armhf/
Replied by andypugh on topic PiDiCNC Control System
I hope the linuxcnc community will start support arm SBC soon. This computers have an SPI interface for what is much more easier build some hobby controller boards than for peripheries what is available on common x86 motherboards.
LinuxCNC is built and tested on ARM but AFAIK only on armhf.
You can see all the platforms that the buildbot test-compiles for here:
buildbot.linuxcnc.org/buildbot/waterfall
If using Jessie, there are even packages: buildbot.linuxcnc.org/dists/jessie/maste...reempt/binary-armhf/
Please Log in or Create an account to join the conversation.
- mngr0
- Offline
- Junior Member
-
Less
More
- Posts: 26
- Thank you received: 1
30 Jul 2018 08:59 #115108
by mngr0
Replied by mngr0 on topic PiDiCNC Control System
Hi,
Tom, can you please share the configuration file you used for the pidiCNC?
Tom, can you please share the configuration file you used for the pidiCNC?
Please Log in or Create an account to join the conversation.
- tommylight
-
- Away
- Moderator
-
Less
More
- Posts: 20843
- Thank you received: 7106
30 Jul 2018 09:25 #115112
by tommylight
Replied by tommylight on topic PiDiCNC Control System
Here you go.
Please Log in or Create an account to join the conversation.
- mngr0
- Offline
- Junior Member
-
Less
More
- Posts: 26
- Thank you received: 1
30 Jul 2018 09:55 #115113
by mngr0
Replied by mngr0 on topic PiDiCNC Control System
Thank you!!
where did you install pidi from? is it open source?
loadrt pidi Board0=3805,11111,1111111 Board1=3811Please Log in or Create an account to join the conversation.
- tommylight
-
- Away
- Moderator
-
Less
More
- Posts: 20843
- Thank you received: 7106
30 Jul 2018 11:05 #115116
by tommylight
Replied by tommylight on topic PiDiCNC Control System
They sent me a link to download the image and removed it promptly after i did.
That was very strange as it should be available, it is machinekit so open source.
That was very strange as it should be available, it is machinekit so open source.
The following user(s) said Thank You: Mike_Eitel
Please Log in or Create an account to join the conversation.
- mngr0
- Offline
- Junior Member
-
Less
More
- Posts: 26
- Thank you received: 1
30 Jul 2018 12:32 #115128
by mngr0
Replied by mngr0 on topic PiDiCNC Control System
my machinekit instance has no pidino pidi found in machinekit repository
I guess I will do without it
Thanks tom
do_load_cmd: dlopen: pidi.so: cannot open shared object file: No such file or directoryI guess I will do without it
Thanks tom
Please Log in or Create an account to join the conversation.
- viktan
- Offline
- Senior Member
-
Less
More
- Posts: 40
- Thank you received: 7
02 Aug 2018 20:32 #115435
by viktan
Replied by viktan on topic PiDiCNC Control System
Hi mngr0,
I saw your message earlier but I'm busy these days. I will send you an image with preinstaled machinekit and pidi driver. I have a good news, this image have working opengl acceleration.
As Tom mentioned I sent him an image, but I did not delete it. I sent it over myairbridge.com where is restriction for free plan that they keep files only for 2 days
Viktor
I saw your message earlier but I'm busy these days. I will send you an image with preinstaled machinekit and pidi driver. I have a good news, this image have working opengl acceleration.
As Tom mentioned I sent him an image, but I did not delete it. I sent it over myairbridge.com where is restriction for free plan that they keep files only for 2 days
Viktor
The following user(s) said Thank You: tommylight
Please Log in or Create an account to join the conversation.
- mngr0
- Offline
- Junior Member
-
Less
More
- Posts: 26
- Thank you received: 1
02 Aug 2018 20:43 #115438
by mngr0
Replied by mngr0 on topic PiDiCNC Control System
Hi Vitkan,
Thank you for the offer, as I am writing a mesa-like firmware I am interested in the source code primarily. My objective is understanding how the hostmot2 communication goes.
Can you give it too?
Until now I tried looking both in the FPGA side and in the LinuxCNC side, but with no luck.
If you, or anyone, could help me with that I would really appreciate
Thank you for the offer, as I am writing a mesa-like firmware I am interested in the source code primarily. My objective is understanding how the hostmot2 communication goes.
Can you give it too?
Until now I tried looking both in the FPGA side and in the LinuxCNC side, but with no luck.
If you, or anyone, could help me with that I would really appreciate
Please Log in or Create an account to join the conversation.
- viktan
- Offline
- Senior Member
-
Less
More
- Posts: 40
- Thank you received: 7
06 Aug 2018 21:02 #115691
by viktan
Replied by viktan on topic PiDiCNC Control System
Hi Mngr0,
First of all, our boards are not based on any Mesa boards or hostmot software. We inspired on driver from kinsamanka who made a driver which can communicate with his board over SPI.
I sending you source files, maybe could be helpful. It is only for Raspberry Pi and for communication over SPI
First of all, our boards are not based on any Mesa boards or hostmot software. We inspired on driver from kinsamanka who made a driver which can communicate with his board over SPI.
I sending you source files, maybe could be helpful. It is only for Raspberry Pi and for communication over SPI
The following user(s) said Thank You: tommylight
Please Log in or Create an account to join the conversation.
- markd
-
- Visitor
-
01 Mar 2019 20:34 #127457
by markd
Replied by markd on topic PiDiCNC Control System
Has there been any progress on these boards?
Have you got a price yet?
Have you got a price yet?
Please Log in or Create an account to join the conversation.
Moderators: PCW, jmelson
Time to create page: 0.112 seconds