7i76e start up error
16 Jul 2021 00:00 #214952
by kelargo
Replied by kelargo on topic 7i76e start up error
oh, I switch to "performance"
cpupower frequency-set --governor performance
papa@linuxcnc:~$ halcmd show param *.tmax
Parameters:
Owner Type Dir Value Name
26 s32 RW 0 hm2_7i76e.0.read-request.tmax
26 s32 RW 479298 hm2_7i76e.0.read.tmax
26 s32 RW 65046 hm2_7i76e.0.write.tmax
19 s32 RW 5180 motion-command-handler.tmax
19 s32 RW 41958 motion-controller.tmax
29 s32 RW 2294 pid.s.do-pid-calcs.tmax
29 s32 RW 4884 pid.x.do-pid-calcs.tmax
29 s32 RW 2590 pid.x2.do-pid-calcs.tmax
29 s32 RW 2368 pid.y.do-pid-calcs.tmax
29 s32 RW 2368 pid.z.do-pid-calcs.tmax
20 s32 RW 583231 servo-thread.tmax
cpupower frequency-set --governor performance
papa@linuxcnc:~$ halcmd show param *.tmax
Parameters:
Owner Type Dir Value Name
26 s32 RW 0 hm2_7i76e.0.read-request.tmax
26 s32 RW 479298 hm2_7i76e.0.read.tmax
26 s32 RW 65046 hm2_7i76e.0.write.tmax
19 s32 RW 5180 motion-command-handler.tmax
19 s32 RW 41958 motion-controller.tmax
29 s32 RW 2294 pid.s.do-pid-calcs.tmax
29 s32 RW 4884 pid.x.do-pid-calcs.tmax
29 s32 RW 2590 pid.x2.do-pid-calcs.tmax
29 s32 RW 2368 pid.y.do-pid-calcs.tmax
29 s32 RW 2368 pid.z.do-pid-calcs.tmax
20 s32 RW 583231 servo-thread.tmax
Please Log in or Create an account to join the conversation.
- tommylight
- Offline
- Moderator
Less
More
- Posts: 17767
- Thank you received: 5905
16 Jul 2021 00:44 #214962
by tommylight
Replied by tommylight on topic 7i76e start up error
Change the 5V power supply ???
Please Log in or Create an account to join the conversation.
16 Jul 2021 01:01 #214969
by kelargo
Replied by kelargo on topic 7i76e start up error
I have 24v powered in, as described in that one PDF.
TB1 field power pin 8 GND, pin 5 +24V
TB3 power pin 23 : GND and pin 22 _24 V
is this good, now ?
20 s32 RW 583231 servo-thread.tmax
TB1 field power pin 8 GND, pin 5 +24V
TB3 power pin 23 : GND and pin 22 _24 V
is this good, now ?
20 s32 RW 583231 servo-thread.tmax
Please Log in or Create an account to join the conversation.
16 Jul 2021 01:32 #214974
by PCW
Replied by PCW on topic 7i76e start up error
Should be fine for a 1 KHz servo thread
Please Log in or Create an account to join the conversation.
Time to create page: 0.078 seconds