General LinuxCNC Questions 6188 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
QTPlasmaC THC slow to respond causing arc loss Topic started 28 May 2021 13:39, by bevins Last Post 30 May 2021 04:06 by phillc54 1 2	Replies:10 Views:2357	Last Post by phillc54 30 May 2021 04:06
Linuxcnc stops after manual tool change dialogue Topic started 27 May 2021 16:35, by Sviper Last Post 27 May 2021 16:57 by Sviper	Replies:1 Views:880	Sviper Last Post by Sviper 27 May 2021 16:57
Strange stepper issue at startup Topic started 27 May 2021 13:09, by Gregor96 Last Post 27 May 2021 13:28 by PCW	Replies:1 Views:815	Last Post by PCW 27 May 2021 13:28
Raspberry Pi 4 7i90 on Mojo V3 board Topic started 18 May 2021 08:22, by rbobey1989 Last Post 27 May 2021 06:57 by cakeslob 1 2	Replies:17 Views:4209	cakeslob Last Post by cakeslob 27 May 2021 06:57
Blacklash Sódick A320 Topic started 25 May 2021 15:22, by NORMAR4 Last Post 26 May 2021 19:02 by andypugh	Replies:3 Views:869	Last Post by andypugh 26 May 2021 19:02
Connect to 7I80 Topic started 25 May 2021 10:56, by nhanpham Last Post 26 May 2021 02:59 by nhanpham	Replies:4 Views:1091	Last Post by nhanpham 26 May 2021 02:59
Set up parallel port as input _ hardware Topic started 24 May 2021 20:49, by Nordle Last Post 25 May 2021 21:31 by andypugh	Replies:9 Views:2623	Last Post by andypugh 25 May 2021 21:31
axis job image and toolpath image Topic started 24 May 2021 04:09, by ericg Last Post 25 May 2021 11:33 by ericg	Replies:2 Views:858	ericg Last Post by ericg 25 May 2021 11:33
Issues with new Build - Mesa 7i96 + DM542T Topic started 24 May 2021 19:46, by Twitchy Last Post 25 May 2021 02:37 by Twitchy	Replies:4 Views:1098	Twitchy Last Post by Twitchy 25 May 2021 02:37
How to test real-time performance of linuxCNC RTAI? Topic started 23 May 2021 01:47, by hitmanlinuxcnc Last Post 25 May 2021 00:48 by hitmanlinuxcnc	Replies:8 Views:1826	hitmanlinuxcnc Last Post by hitmanlinuxcnc 25 May 2021 00:48
Parallel Port Via m.2 Topic started 09 Nov 2019 19:10, by Penguin Last Post 24 May 2021 23:31 by tommylight	Replies:5 Views:2611	Last Post by tommylight 24 May 2021 23:31
Setting up threading on a Boxford 160TCL lathe Topic started 01 May 2021 18:02, by rider-83 Last Post 24 May 2021 21:35 by andypugh 1 2 3	Replies:25 Views:4229	Last Post by andypugh 24 May 2021 21:35
Path in Fusion360 different from actual path Topic started 20 May 2021 14:55, by mf290997 Last Post 24 May 2021 00:41 by BigJohnT	Replies:7 Views:1503	Last Post by BigJohnT 24 May 2021 00:41
Raspberry Pi 4 RT PREEMPT KERNEL Xbox one controller Topic started 23 May 2021 09:54, by rbobey1989 Last Post 23 May 2021 20:32 by rbobey1989 1 2	Replies:11 Views:3746	Last Post by rbobey1989 23 May 2021 20:32
Rigid tapping with only A and Z signals Topic started 20 May 2021 01:50, by psz Last Post 21 May 2021 19:22 by Aaroncnc	Replies:5 Views:1299	Aaroncnc Last Post by Aaroncnc 21 May 2021 19:22
Control panel fans Topic started 19 May 2021 11:41, by bevins Last Post 20 May 2021 08:01 by aleksamc	Replies:4 Views:941	Last Post by aleksamc 20 May 2021 08:01
Another unexpected realtime delay on task 0 with Mesa 7i76E Topic started 18 May 2021 18:24, by Sandro Last Post 19 May 2021 18:57 by PCW	Replies:3 Views:1216	Last Post by PCW 19 May 2021 18:57
QTPlasmaC Stainless Steel Topic started 19 May 2021 00:20, by bevins Last Post 19 May 2021 11:33 by bevins	Replies:2 Views:816	Last Post by bevins 19 May 2021 11:33
basic question about Driver input signals Topic started 14 May 2021 21:37, by acourtjester Last Post 17 May 2021 23:45 by rollfree 1 2	Replies:13 Views:3572	rollfree Last Post by rollfree 17 May 2021 23:45
Stepper motors run free when enable is inactive Topic started 17 May 2021 20:37, by Gordon49 Last Post 17 May 2021 22:05 by tommylight	Replies:1 Views:923	Last Post by tommylight 17 May 2021 22:05

Time to create page: 0.532 seconds