General LinuxCNC Questions 6665 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Constant loss of position Topic started 26 Sep 2024 13:35, by andreabonuc Last Post 29 Sep 2024 17:39 by andreabonuc 1 2 3 4	Replies:31 Views:1801	andreabonuc Last Post by andreabonuc 29 Sep 2024 17:39
Switching from MDI to Manual control causes an issue in the Joint positions Topic started 28 Sep 2024 11:53, by Ahmed.emara Last Post 29 Sep 2024 11:10 by Aciera	Replies:3 Views:351	Last Post by Aciera 29 Sep 2024 11:10
Decent servo suppliers and recommendations Topic started 28 Sep 2024 00:52, by bentiggin Last Post 28 Sep 2024 13:59 by ihavenofish 1 2	Replies:10 Views:1152	ihavenofish Last Post by ihavenofish 28 Sep 2024 13:59
are there any one on one tutor or consultant Topic started 27 Sep 2024 15:15, by akim14 Last Post 27 Sep 2024 15:23 by tommylight	Replies:1 Views:234	Last Post by tommylight 27 Sep 2024 15:23
Linuxcnc and Baldor flexdrive 2 drivers Topic started 03 Apr 2023 17:35, by kn612 Last Post 25 Sep 2024 14:07 by PCW	Replies:3 Views:911	Last Post by PCW 25 Sep 2024 14:07
how to optimising long time servo-thread.tmax (mesa 7i92, i7 3770) Topic started 25 Sep 2024 03:02, by AnkerFly Last Post 25 Sep 2024 13:57 by PCW	Replies:6 Views:531	Last Post by PCW 25 Sep 2024 13:57
Basic 2 Axis Lathe Topic started 24 Sep 2024 09:14, by hhscott Last Post 24 Sep 2024 15:52 by hhscott	Replies:2 Views:296	hhscott Last Post by hhscott 24 Sep 2024 15:52
New and overwhelmed. Topic started 18 Sep 2024 18:13, by 2703adam Last Post 24 Sep 2024 15:45 by Todd Zuercher 1 2	Replies:11 Views:1077	Last Post by Todd Zuercher 24 Sep 2024 15:45
No 7c81 board found Topic started 24 Sep 2024 12:09, by uzairk Last Post 24 Sep 2024 13:58 by PCW	Replies:1 Views:249	Last Post by PCW 24 Sep 2024 13:58
Control Can bus Topic started 23 Sep 2024 09:32, by TheRoslyak Last Post 24 Sep 2024 00:04 by Benb	Replies:1 Views:592	Last Post by Benb 24 Sep 2024 00:04
z axis inverted in NC file Topic started 23 Aug 2024 20:36, by rbarry1068 Last Post 23 Sep 2024 15:24 by rbarry1068	Replies:6 Views:396	rbarry1068 Last Post by rbarry1068 23 Sep 2024 15:24
kernel upgrade on Debian Buster Topic started 21 Sep 2024 10:50, by papagno-source Last Post 22 Sep 2024 07:31 by papagno-source	Replies:4 Views:515	papagno-source Last Post by papagno-source 22 Sep 2024 07:31
jogging using USB DragonRise pendant Topic started 21 Sep 2024 03:42, by frayja2002 Last Post 22 Sep 2024 01:02 by frayja2002	Replies:5 Views:418	frayja2002 Last Post by frayja2002 22 Sep 2024 01:02
Calibrating A axis Topic started 20 Sep 2024 07:37, by Mae22 Last Post 21 Sep 2024 20:54 by Masiwood123	Replies:7 Views:572	Last Post by Masiwood123 21 Sep 2024 20:54
Anyone running Arduino IDE on a LinuxCNC machine Topic started 19 Sep 2024 20:48, by slowpoke Last Post 20 Sep 2024 12:42 by slowpoke	Replies:2 Views:402	slowpoke Last Post by slowpoke 20 Sep 2024 12:42
SCARA Vismach - Gcode error "exceed C's positive limit" Topic started 18 Sep 2024 10:22, by DPFlex Last Post 19 Sep 2024 21:48 by raf1110	Replies:6 Views:487	Last Post by raf1110 19 Sep 2024 21:48
Probe Basic / Touch Probe Topic started 10 Sep 2024 21:21, by crazycajun Last Post 19 Sep 2024 13:42 by Unlogic 1 2	Replies:15 Views:1154	Unlogic Last Post by Unlogic 19 Sep 2024 13:42
THC problem Topic started 30 May 2024 21:53, by acourtjester Last Post 19 Sep 2024 02:30 by Diegot 1 2 3 ... 5	Replies:46 Views:3526	Last Post by Diegot 19 Sep 2024 02:30
Running Gcode Program with G54 without any tool offsets Topic started 16 Sep 2024 23:41, by upplib Last Post 17 Sep 2024 17:13 by upplib	Replies:4 Views:531	upplib Last Post by upplib 17 Sep 2024 17:13
What is going on with the buildbot? Topic started 15 Sep 2024 16:07, by Aciera Last Post 17 Sep 2024 10:26 by rodw 1 2	Replies:17 Views:1481	Last Post by rodw 17 Sep 2024 10:26

Time to create page: 0.325 seconds