Basic Configuration 1297 topics

A place to discuss basic configurations like probe input, homing etc.

Subject	Replies / Views	Last Post
LinuxCNC does not follow gcode layout Topic started 06 May 2014 01:53, by HolgerT Last Post 06 May 2014 06:59 by andypugh	Replies:3 Views:1441	Last Post by andypugh 06 May 2014 06:59
How to reverse direction on servo motor Topic started 02 May 2014 01:55, by greeder88 Last Post 02 May 2014 13:39 by PCW	Replies:3 Views:2306	Last Post by PCW 02 May 2014 13:39
3axis CNC retrofitting with LinuxCNC Topic started 29 Mar 2014 20:09, by terans1085 Last Post 29 Apr 2014 13:25 by terans1085 1 2	Replies:10 Views:4077	Last Post by terans1085 29 Apr 2014 13:25
another limit issue/homing issue Topic started 26 Apr 2014 22:26, by rotccapt Last Post 28 Apr 2014 23:45 by cncbasher 1 2	Replies:10 Views:4486	cncbasher Last Post by cncbasher 28 Apr 2014 23:45
8i20 brushless servo drive output amps Topic started 21 Apr 2014 20:22, by johns00056 Last Post 25 Apr 2014 06:52 by andypugh 1 2	Replies:12 Views:3888	Last Post by andypugh 25 Apr 2014 06:52
Homing process for 5i25/7i76 with 5 axes Topic started 17 Apr 2014 04:12, by tnl.lambert Last Post 18 Apr 2014 22:55 by PCW 1 2	Replies:11 Views:4918	Last Post by PCW 18 Apr 2014 22:55
simple laser cutter ON/OFF control (Z-axis) Topic started 14 Apr 2014 20:19, by leintz Last Post 15 Apr 2014 18:23 by andypugh 1 2	Replies:11 Views:5714	Last Post by andypugh 15 Apr 2014 18:23
5i22 / 7i77 limit switches Topic started 14 Apr 2014 08:23, by greeder88 Last Post 14 Apr 2014 19:12 by jtc	Replies:2 Views:1450	Last Post by jtc 14 Apr 2014 19:12
8i20 brushless servo hall sensor set up Topic started 02 Apr 2014 01:52, by johns00056 Last Post 14 Apr 2014 04:30 by PCW 1 2	Replies:17 Views:4918	Last Post by PCW 14 Apr 2014 04:30
custom M code Topic started 08 Apr 2014 00:37, by viski Last Post 11 Apr 2014 02:13 by viski	Replies:3 Views:1766	viski Last Post by viski 11 Apr 2014 02:13
Jog in oposit direction when hit pos/neg limit sw Topic started 10 Apr 2014 17:56, by jtc Last Post 10 Apr 2014 20:22 by Todd Zuercher	Replies:3 Views:1545	Last Post by Todd Zuercher 10 Apr 2014 20:22
rpm sync with spindle and motor Topic started 09 Apr 2014 07:05, by b2unit Last Post 09 Apr 2014 09:28 by PCW	Replies:1 Views:1747	Last Post by PCW 09 Apr 2014 09:28
Using Touch Off with Soft Limits Topic started 05 Apr 2014 10:54, by J64 Last Post 08 Apr 2014 14:10 by Rick G	Replies:9 Views:2410	Last Post by Rick G 08 Apr 2014 14:10
Requested tool 4 not found in the tool table Topic started 05 Apr 2014 02:56, by 71GA Last Post 05 Apr 2014 03:20 by emcPT	Replies:1 Views:2971	Last Post by emcPT 05 Apr 2014 03:20
Multiple Probes? Topic started 03 Apr 2014 20:59, by library Last Post 05 Apr 2014 01:32 by library	Replies:4 Views:2327	library Last Post by library 05 Apr 2014 01:32
spindle encoder setup in hal Topic started 01 Apr 2014 06:51, by b2unit Last Post 04 Apr 2014 15:39 by b2unit 1 2	Replies:10 Views:11.6k	b2unit Last Post by b2unit 04 Apr 2014 15:39
Program exceeds machine maximum on axis Z. Topic started 02 Apr 2014 23:59, by 71GA Last Post 03 Apr 2014 18:31 by BigJohnT	Replies:4 Views:6618	Last Post by BigJohnT 03 Apr 2014 18:31
Wire size for controller board Topic started 30 Mar 2014 04:42, by jonesturf Last Post 30 Mar 2014 07:26 by andypugh	Replies:2 Views:1510	Last Post by andypugh 30 Mar 2014 07:26
Positioning Accuracy Not Working as Desired Topic started 29 Mar 2014 00:12, by fbx109 Last Post 29 Mar 2014 00:12 by fbx109	Replies:0 Views:1580	fbx109 Last Post by fbx109 29 Mar 2014 00:12
Limit Switch Selection Topic started 25 Mar 2014 08:46, by danimal300 Last Post 25 Mar 2014 18:32 by ArcEye	Replies:2 Views:1708	ArcEye Last Post by ArcEye 25 Mar 2014 18:32

Time to create page: 0.225 seconds