Basic Configuration 1390 topics

A place to discuss basic configurations like probe input, homing etc.

Subject	Replies / Views	Last Post
Poor/no response in EMC control vs. PnCConf Topic started 23 Sep 2011 02:23, by NICKKINSMAN Last Post 02 Dec 2015 00:55 by cmtunnel 1 2	Replies:16 Views:9185	cmtunnel Last Post by cmtunnel 02 Dec 2015 00:55
Slaving the second gantry motor (7i92) Topic started 05 Nov 2015 17:49, by dannym Last Post 28 Nov 2015 17:27 by blacksmith 1 2	Replies:19 Views:3519	blacksmith Last Post by blacksmith 28 Nov 2015 17:27
steppers initially rotate then stop when jogging Topic started 15 Nov 2015 20:21, by megazoic Last Post 17 Nov 2015 18:17 by megazoic 1 2	Replies:11 Views:3108	megazoic Last Post by megazoic 17 Nov 2015 18:17
Modifying parallel port Topic started 09 Nov 2015 18:08, by Micromet Last Post 16 Nov 2015 18:39 by Todd Zuercher 1 2	Replies:15 Views:4721	Last Post by Todd Zuercher 16 Nov 2015 18:39
Driver Timing settings for Other in stepconf Topic started 13 Nov 2015 19:41, by megazoic Last Post 15 Nov 2015 19:58 by megazoic 1 2	Replies:10 Views:3941	megazoic Last Post by megazoic 15 Nov 2015 19:58
Debian jessie + Mesa 7i76E Topic started 04 Nov 2015 05:37, by jtc Last Post 13 Nov 2015 13:04 by jtc	Replies:8 Views:3139	Last Post by jtc 13 Nov 2015 13:04
Any final solution for MaxNC Open Loop? Topic started 07 Nov 2015 05:21, by catacluj Last Post 10 Nov 2015 11:11 by cncbasher 1 2	Replies:10 Views:4140	cncbasher Last Post by cncbasher 10 Nov 2015 11:11
Sim toolchange-with-length-switch basic questions? Topic started 09 Nov 2015 19:55, by TroyO Last Post 10 Nov 2015 10:01 by andypugh	Replies:4 Views:1052	Last Post by andypugh 10 Nov 2015 10:01
XZA Milling Machine need Help Topic started 08 Nov 2015 21:13, by Sergio Last Post 09 Nov 2015 19:14 by Sergio	Replies:6 Views:1549	Sergio Last Post by Sergio 09 Nov 2015 19:14
Cycle Start / Pause / Resume-Button Topic started 07 Nov 2015 01:21, by DaPeace Last Post 09 Nov 2015 17:06 by andypugh	Replies:4 Views:4703	Last Post by andypugh 09 Nov 2015 17:06
Stepper motors only move in one direction Topic started 05 Nov 2015 08:08, by cardinalbotics Last Post 09 Nov 2015 09:40 by cncbasher	Replies:6 Views:3292	cncbasher Last Post by cncbasher 09 Nov 2015 09:40
servo dac offset Topic started 31 Oct 2015 18:59, by bkt Last Post 07 Nov 2015 18:50 by bkt 1 2 3 ... 5	Replies:49 Views:8624	Last Post by bkt 07 Nov 2015 18:50
Mesa 7i76 time out error Topic started 31 Oct 2015 15:54, by AntonM Last Post 02 Nov 2015 11:41 by Diederik 1 2	Replies:11 Views:3994	Last Post by Diederik 02 Nov 2015 11:41
Touch probe and auto tool length measurement Topic started 29 Oct 2015 05:24, by spangledboy Last Post 02 Nov 2015 00:32 by spangledboy	Replies:2 Views:1782	Last Post by spangledboy 02 Nov 2015 00:32
AC Servo: Analog or Step/Dir? Topic started 28 Oct 2015 11:00, by buckym1a Last Post 28 Oct 2015 19:36 by andypugh	Replies:2 Views:3685	Last Post by andypugh 28 Oct 2015 19:36
configuration of TB6560 controller & variants Topic started 29 Aug 2012 08:20, by cncbasher Last Post 21 Oct 2015 19:11 by bwg 1 2	Replies:15 Views:49.3k	bwg Last Post by bwg 21 Oct 2015 19:11
Set Default Value for Rotary Encoder-Knob Topic started 19 Oct 2015 14:39, by DaPeace Last Post 20 Oct 2015 23:54 by DaPeace	Replies:6 Views:1684	DaPeace Last Post by DaPeace 20 Oct 2015 23:54
Newbie configuration problem.... HELP! Topic started 12 Oct 2015 03:04, by jessedavis Last Post 15 Oct 2015 21:06 by jessedavis	Replies:3 Views:1306	jessedavis Last Post by jessedavis 15 Oct 2015 21:06
keystroke as a hal pin? Topic started 01 Oct 2015 19:12, by jtc Last Post 08 Oct 2015 05:05 by jtc 1 2	Replies:10 Views:4865	Last Post by jtc 08 Oct 2015 05:05
error message "P value out of range with G10 L1" Topic started 30 Sep 2015 03:12, by b2unit Last Post 01 Oct 2015 22:05 by b2unit 1 2	Replies:10 Views:3899	b2unit Last Post by b2unit 01 Oct 2015 22:05

Time to create page: 0.163 seconds