HAL 1411 topics

Discussion on HAL (Hardware Abstract Layer}
Category		Last Post
	HAL Examples 65 topics A place to post finished examples using HAL Moderators: tommylight, Aciera, snowgoer540	Re: Emulating lathe compound angle ... by slowpoke 29 Jun 2025 19:25

Subject	Replies / Views	Last Post
Step/Dir Servo Closed Loop with Encoder Topic started 11 Aug 2019 06:28, by Type_Zero_Design Last Post 13 Aug 2019 18:37 by andypugh	Replies:2 Views:1938	Last Post by andypugh 13 Aug 2019 18:37
Threadjack> Why did I get into CNC was ...What is hal? Topic started 01 Aug 2019 17:15, by Dinuka_Shehan Last Post 13 Aug 2019 15:53 by tommylight 1 2	Replies:17 Views:3382	Last Post by tommylight 13 Aug 2019 15:53
Feed override net to rapid override Topic started 27 Jul 2019 14:22, by JB-Motoring Last Post 01 Aug 2019 20:35 by JB-Motoring 1 2	Replies:10 Views:3767	JB-Motoring Last Post by JB-Motoring 01 Aug 2019 20:35
Axis Y two motors gantry with separate switch home-offset Topic started 20 Jul 2019 17:07, by Maxardi99 Last Post 30 Jul 2019 09:59 by phillc54 1 2	Replies:18 Views:4307	Last Post by phillc54 30 Jul 2019 09:59
Usage of an external library (bcm2835) with halcompile Topic started 24 Jul 2019 07:43, by wicki Last Post 26 Jul 2019 23:02 by Grotius	Replies:8 Views:1561	Last Post by Grotius 26 Jul 2019 23:02
Lathe Collet User Mcode Topic started 19 Jul 2019 16:12, by Erikcnc Last Post 21 Jul 2019 14:13 by Erikcnc	Replies:6 Views:1234	Last Post by Erikcnc 21 Jul 2019 14:13
identify in HAL when Linuxcnc is doing drilling operation (G83/G76...) Topic started 09 Jul 2019 11:00, by ahhkoch Last Post 15 Jul 2019 13:41 by andypugh	Replies:7 Views:1415	Last Post by andypugh 15 Jul 2019 13:41
Parallel port problems on new build; pins 14 and 16 not working for spindle Topic started 03 Jul 2019 17:39, by trebuchetguy Last Post 09 Jul 2019 01:40 by Grotius 1 2 3 4	Replies:31 Views:5093	Last Post by Grotius 09 Jul 2019 01:40
Switch between halui.jog.N.plus and halui.jog.N.increment-plus Topic started 04 Jul 2019 11:20, by Robban Last Post 05 Jul 2019 15:03 by andypugh	Replies:2 Views:1297	Last Post by andypugh 05 Jul 2019 15:03
Actually turning the spindle off, not just temporarily inhibiting it. Topic started 26 Jun 2019 09:51, by JetForMe Last Post 29 Jun 2019 18:10 by cmorley	Replies:6 Views:1402	cmorley Last Post by cmorley 29 Jun 2019 18:10
More control over waiting for the spindle to come up to speed? Topic started 26 Jun 2019 22:26, by JetForMe Last Post 28 Jun 2019 01:18 by JetForMe	Replies:8 Views:2649	Last Post by JetForMe 28 Jun 2019 01:18
2.9-pre, not able to configure pwm signal Topic started 26 Jun 2019 15:33, by llamatrails Last Post 27 Jun 2019 23:16 by llamatrails	Replies:5 Views:2479	llamatrails Last Post by llamatrails 27 Jun 2019 23:16
need a smarter rule than this simple combinatorial logic for controlling the ATC Topic started 27 Jun 2019 11:14, by JetForMe Last Post 27 Jun 2019 20:49 by PCW	Replies:3 Views:1022	Last Post by PCW 27 Jun 2019 20:49
Setting a signal to a constant value Topic started 26 Jun 2019 09:22, by JetForMe Last Post 27 Jun 2019 10:27 by pl7i92 1 2	Replies:10 Views:3709	Last Post by pl7i92 27 Jun 2019 10:27
Configuring the spindle motor's power draw bar (tool change) Topic started 21 Jun 2019 06:01, by JetForMe Last Post 25 Jun 2019 11:34 by andypugh	Replies:7 Views:1462	Last Post by andypugh 25 Jun 2019 11:34
HAL code for hobbing Topic started 10 Mar 2018 03:27, by jherzvt Last Post 23 Jun 2019 21:49 by andypugh	Replies:3 Views:2070	Last Post by andypugh 23 Jun 2019 21:49
stepgen for dummies Topic started 23 Jun 2019 14:57, by felixcnc Last Post 23 Jun 2019 20:08 by PCW	Replies:3 Views:1826	Last Post by PCW 23 Jun 2019 20:08
Parallel Port -> 4-bit DAC driven monolothic chopper controller Topic started 13 May 2019 19:14, by fungus Last Post 17 Jun 2019 02:08 by fungus 1 2	Replies:18 Views:3287	fungus Last Post by fungus 17 Jun 2019 02:08
I cannot Un-Emergancy Stop [X] or Press Power [ \| ] in Linux CNC Topic started 10 May 2018 03:05, by BrendaEM Last Post 01 Jun 2019 11:43 by bevins	Replies:4 Views:3281	Last Post by bevins 01 Jun 2019 11:43
Edge time not long enough Topic started 22 May 2019 05:15, by Nico2017 Last Post 23 May 2019 19:02 by Todd Zuercher	Replies:5 Views:1295	Last Post by Todd Zuercher 23 May 2019 19:02

Time to create page: 0.176 seconds

HAL 1411 topics

HAL Examples 65 topics