General LinuxCNC Questions 6025 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
How to change the direction of the X and Y axes in Linuxcnc by changing entries Topic started 17 Jan 2022 17:50, by jarcysgru Last Post 21 Jan 2022 18:56 by rodw 1 2	Replies:14 Views:2814	Last Post by rodw 21 Jan 2022 18:56
LCNC 2.8 RPI4 - File system bug Topic started 21 Jan 2022 12:24, by zz912 Last Post 21 Jan 2022 16:48 by zz912	Replies:6 Views:730	Last Post by zz912 21 Jan 2022 16:48
pausing execution of G-code Topic started 18 Jan 2022 07:22, by sm Last Post 19 Jan 2022 16:45 by sm	Replies:8 Views:2897	sm Last Post by sm 19 Jan 2022 16:45
error message "joint 1 amp fault" Topic started 18 Jan 2022 11:15, by sibelius Last Post 19 Jan 2022 06:33 by sibelius	Replies:3 Views:1619	Last Post by sibelius 19 Jan 2022 06:33
Running milltask (or gcode interp) without python? Topic started 05 Jan 2022 13:56, by mungkie Last Post 19 Jan 2022 00:35 by mungkie 1 2	Replies:10 Views:2504	mungkie Last Post by mungkie 19 Jan 2022 00:35
7i76e Topic started 09 Jan 2022 02:23, by Aldenflorio Last Post 18 Jan 2022 17:23 by Clive S 1 2 3 ... 8	Replies:77 Views:8805	Clive S Last Post by Clive S 18 Jan 2022 17:23
SUNIX PCI parallel port cards Topic started 03 Aug 2018 14:39, by chorler Last Post 17 Jan 2022 20:30 by chorler	Replies:2 Views:1573	chorler Last Post by chorler 17 Jan 2022 20:30
No motion after homing Z Topic started 17 Jan 2022 14:25, by Jake Last Post 17 Jan 2022 19:02 by Jake	Replies:2 Views:700	Jake Last Post by Jake 17 Jan 2022 19:02
M6 and Manual Tool change Topic started 16 Jan 2022 17:13, by Ewok2 Last Post 16 Jan 2022 22:51 by Ewok2	Replies:4 Views:1449	Ewok2 Last Post by Ewok2 16 Jan 2022 22:51
Wabeco D6000: ATC problem Topic started 12 May 2021 16:13, by gcardinal Last Post 16 Jan 2022 22:18 by andypugh	Replies:6 Views:1626	Last Post by andypugh 16 Jan 2022 22:18
Parallel port controller issues, can not find address Topic started 18 Dec 2021 23:34, by Jake Last Post 15 Jan 2022 16:12 by Jake 1 2 3 ... 5	Replies:40 Views:7366	Jake Last Post by Jake 15 Jan 2022 16:12
Mesa Flash - Mesa 7i94. Topic started 11 Nov 2019 15:55, by Moreira Last Post 15 Jan 2022 15:56 by PCW 1 2 3 4	Replies:32 Views:7217	Last Post by PCW 15 Jan 2022 15:56
Where I can buy Mesa 7i96 Topic started 08 Jan 2022 23:30, by medin998 Last Post 15 Jan 2022 07:44 by tommylight	Replies:1 Views:1080	Last Post by tommylight 15 Jan 2022 07:44
Problem updating from 2.8.0-pre to 2.8.2 Topic started 10 Jan 2022 22:10, by strahlensauger Last Post 14 Jan 2022 23:22 by strahlensauger	Replies:5 Views:819	Last Post by strahlensauger 14 Jan 2022 23:22
Questions about a Mesa 7i76E build with CL86T steppers Topic started 12 Jan 2022 00:24, by tupshin Last Post 13 Jan 2022 17:25 by tupshin	Replies:5 Views:1431	tupshin Last Post by tupshin 13 Jan 2022 17:25
stepper driver setup values? Topic started 12 Jan 2022 01:17, by ncf250sd Last Post 12 Jan 2022 05:50 by tommylight	Replies:2 Views:786	Last Post by tommylight 12 Jan 2022 05:50
Parallel port error in RTAI kernel Topic started 10 Jan 2022 07:41, by rajsekhar Last Post 11 Jan 2022 04:21 by ALittleOffTheRails	Replies:7 Views:1006	Last Post by ALittleOffTheRails 11 Jan 2022 04:21
High Jitter Spikes Topic started 10 Jan 2022 02:15, by Braf1895 Last Post 10 Jan 2022 23:04 by BigJohnT	Replies:3 Views:2233	Last Post by BigJohnT 10 Jan 2022 23:04
LinuxCNC for a high speed 3D printer Topic started 09 Jan 2022 21:05, by ExcessiveO Last Post 10 Jan 2022 22:38 by tommylight	Replies:2 Views:2348	Last Post by tommylight 10 Jan 2022 22:38
Mesaflash: No 7i76e board found Topic started 10 Jan 2022 18:37, by elf Last Post 10 Jan 2022 19:39 by elf	Replies:2 Views:637	elf Last Post by elf 10 Jan 2022 19:39

Time to create page: 0.316 seconds