Prototrak Plus Retrofit with Mesa 7i77 & 5i25 cards

More
04 Feb 2017 15:12 - 27 Apr 2021 14:44 #87296 by new2linux
First, I would like to thank all who make this Forum possible!
I have recovered from prior set back and currently using a pre loaded hard drive (Linux Mint 17.3) from BigJohnT (many thanks) with a 5 vdc power supply at TB1 (on 7i77 card); with W5 & W1 to the Right hand side and W2 on the 5i25 card is in the up spot. Attached are the error, ini and hal files as of the most recent attempt. The DRO does not respond, all the lights look correct on the cards and power supply. The error file states a hal 56 problem, any help would be most warmly welcomed.

many thanks!!

Errors

edit:removed cut and paste

EDIT: This diagram is used with the USdigital encoder.
Attachments:
Last edit: 27 Apr 2021 14:44 by new2linux. Reason: tried attachments, did not work so cut and paste 2nd edit: to include correct diagram

Please Log in or Create an account to join the conversation.

More
04 Feb 2017 16:07 #87297 by bevins
I get this error when I have no VIN on the field voltage connector on 7i77.
The following user(s) said Thank You: new2linux

Please Log in or Create an account to join the conversation.

More
04 Feb 2017 16:18 #87298 by PCW
You are currently shorting out the FPGA cable power by having the
5I25 W2 jumper "up" and 7I77 W5 in the right hand position.

If you use cable cable power you need 5I25 W2 up and 7I77 W5 left
If you use external 5V power for the 7I77 you need 5i25 W2 down and 7I77 W5 right

Unless you have a very good reason, W1 in the 7I77 should always be in the left position
The following user(s) said Thank You: new2linux

Please Log in or Create an account to join the conversation.

More
04 Feb 2017 17:29 #87301 by new2linux
Many thanks PCW, after a closer look and what to look for it appears the CR3 light does not light. If there is no additional control devices, do I need the 24 v power supply and all that goes with it?

many thanks

Please Log in or Create an account to join the conversation.

More
04 Feb 2017 21:26 #87313 by PCW
If you don't use any field I/O (TB7 and TB8) you don't need field power
The following user(s) said Thank You: new2linux

Please Log in or Create an account to join the conversation.

More
06 Feb 2017 21:42 - 06 Feb 2017 21:53 #87421 by new2linux
It appears the CR3 light (located just to the left of TB7, to the top, right on the edge) does not light, I have swapped encoder 0 & 1 "went to" encoder 2 & 3 located at TB3 & TB4; in addition to the associated DRV 0 & 1 "went to" DRV 2 & 3, with the hope, if there was something possibly just goofed up at the original settings. This does not appear to be the case, CR3 light does not light, leaving me to think this card has issues. Does anybody know this to be correct or not.

Many many thanks!!
Last edit: 06 Feb 2017 21:53 by new2linux. Reason: add location of cr3

Please Log in or Create an account to join the conversation.

More
06 Feb 2017 22:21 #87424 by PCW
CR3 will not light (and the 7I77 field I/O section will not work)
unless you have 8 to 32V field power supplied to TB2
The following user(s) said Thank You: new2linux

Please Log in or Create an account to join the conversation.

More
08 Feb 2017 12:08 #87526 by andypugh
What powers the analogout section?
The following user(s) said Thank You: new2linux

Please Log in or Create an account to join the conversation.

More
08 Feb 2017 12:51 - 08 Feb 2017 14:03 #87534 by new2linux
andypugh, thanks for your input, If there are no additional control devices, do I need the 24 v power supply and all that goes with it, going to TB2? Is power required,when the plan has no other devices?

many thanks in advance for any help!!

edit: now I see that this is used for both (analogout section and if you had travel stops or something else) the "powers the analogout section" as per "andypugh" many many thanks! had to read and think about it more to understand that this is the power for the low side of the encoder.
Last edit: 08 Feb 2017 14:03 by new2linux. Reason: had time to think

Please Log in or Create an account to join the conversation.

More
08 Feb 2017 14:50 #87565 by PCW
The 7I77 analog section is powered by the 5V logic power

The 7I77 field I/O section is powered by 8-32V field power
The following user(s) said Thank You: new2linux

Please Log in or Create an account to join the conversation.

Moderators: piasdom
Time to create page: 0.096 seconds
Powered by Kunena Forum