Re:pncconf - feature requests
31 Mar 2011 05:55 - 31 Mar 2011 05:56 #8309
by cmorley
Replied by cmorley on topic Re:pncconf - feature requests
here is a sample config with just random settings:
You may need to edit the mesa load config to get it to run
on 2.4. (the 3pwmgen line)
You may need to edit the mesa load config to get it to run
on 2.4. (the 3pwmgen line)
Last edit: 31 Mar 2011 05:56 by cmorley.
Please Log in or Create an account to join the conversation.
31 Mar 2011 08:51 #8315
by andypugh
Replied by andypugh on topic Re:pncconf - feature requests
Is "numof_3pwmgen" ever a valid modparam? I thought it was "num_3pwmgens".
In either case, it will cause the drivers to not load and emc2 to fail to start with 2.4. On reflection I am not sure that that is the most logical behaviour. Perhaps it should carry on regardless?
In either case, it will cause the drivers to not load and emc2 to fail to start with 2.4. On reflection I am not sure that that is the most logical behaviour. Perhaps it should carry on regardless?
Please Log in or Create an account to join the conversation.
31 Mar 2011 22:50 - 31 Mar 2011 22:50 #8350
by Zig
Replied by Zig on topic Re:pncconf - feature requests
Chris,
attached the current configuration of the machine.
No spindle control. I need to think through the safety interlocks as the spindle has a pneumatic collet. I have to investigate the spindle speed monitor and interlock the air solenoid ( which is presently push button activated ) so that an auto tool changer functionality can be implemented.
So a basic XYZ METRIC machine.
Leadscrews are 5 mm pitch.
Servo motors are directly coupled to the screws.
Linear scale has a basic resolution of 20 micron but in quadrature mode the resolution is 5 micron.
The reader head on the scale outputs an Index pulse for homing as well as an end of travel flag ( a single flag for both positive and negative limits).
attached the current configuration of the machine.
No spindle control. I need to think through the safety interlocks as the spindle has a pneumatic collet. I have to investigate the spindle speed monitor and interlock the air solenoid ( which is presently push button activated ) so that an auto tool changer functionality can be implemented.
So a basic XYZ METRIC machine.
Leadscrews are 5 mm pitch.
Servo motors are directly coupled to the screws.
Linear scale has a basic resolution of 20 micron but in quadrature mode the resolution is 5 micron.
The reader head on the scale outputs an Index pulse for homing as well as an end of travel flag ( a single flag for both positive and negative limits).
Last edit: 31 Mar 2011 22:50 by Zig.
Please Log in or Create an account to join the conversation.
31 Mar 2011 22:52 - 31 Mar 2011 22:52 #8351
by Zig
Replied by Zig on topic Re:pncconf - feature requests
Last edit: 31 Mar 2011 22:52 by Zig.
Please Log in or Create an account to join the conversation.
31 Mar 2011 22:54 #8352
by Zig
Replied by Zig on topic Re:pncconf - feature requests
and the third part of the trilogy ( thank goodnes its not in four parts)
Sorry about this
Sorry about this
Please Log in or Create an account to join the conversation.
31 Mar 2011 23:01 - 31 Mar 2011 23:46 #8353
by Zig
Replied by Zig on topic Re:pncconf - feature requests
and the planned interface electronics
EDIT..file too large
EDIT..file too large
Last edit: 31 Mar 2011 23:46 by Zig.
Please Log in or Create an account to join the conversation.
31 Mar 2011 23:54 #8359
by Zig
Replied by Zig on topic Re:pncconf - feature requests
Please Log in or Create an account to join the conversation.
01 Apr 2011 00:47 #8361
by cmorley
Replied by cmorley on topic Re:pncconf - feature requests
couldn't load this last one...
Please Log in or Create an account to join the conversation.
01 Apr 2011 01:35 - 01 Apr 2011 01:39 #8362
by Zig
Replied by Zig on topic Re:pncconf - feature requests
Chris,
Apologies...
The file was compressed into a RAR format and relabeled as .ZIP to comply with the file extension filter.
This is a more complete drawing
EDIT: still too large
Apologies...
The file was compressed into a RAR format and relabeled as .ZIP to comply with the file extension filter.
This is a more complete drawing
EDIT: still too large
Last edit: 01 Apr 2011 01:39 by Zig.
Please Log in or Create an account to join the conversation.
01 Apr 2011 01:45 - 01 Apr 2011 01:49 #8363
by Zig
Replied by Zig on topic Re:pncconf - feature requests
Updated schematic diagram ( atium DXp 2004 version available)
EDIT:
Ought we move this to a separatetopic?
EDIT:
Ought we move this to a separatetopic?
Last edit: 01 Apr 2011 01:49 by Zig.
Please Log in or Create an account to join the conversation.
Moderators: cmorley
Time to create page: 0.118 seconds