Recent Topics (158 topics)

Subject	Replies / Views	Last Post

Problem with PROBE tab after running a program Category: Qtvcp Topic started 10 Jul 2026 10:13, by RoberCNC Last Post 16 Jul 2026 01:54 by cmorley 1 2	Replies:17 Views:1509	cmorley Last Post by cmorley 16 Jul 2026 01:54
I hate the 7i97T Category: Configuration Tools Topic started 11 Jul 2026 10:24, by Onkelmat Last Post 15 Jul 2026 22:30 by rodw 1 2	Replies:15 Views:1512	Last Post by rodw 15 Jul 2026 22:30
Getting Trixie to play nice Category: General LinuxCNC Questions Topic started 15 Jul 2026 07:57, by aaron Last Post 15 Jul 2026 12:55 by tuxcnc	Replies:2 Views:329	tuxcnc Last Post by tuxcnc 15 Jul 2026 12:55
Trixy Install problems Category: General LinuxCNC Questions Topic started 08 Jul 2026 20:47, by aaron Last Post 15 Jul 2026 11:11 by rodw	Replies:8 Views:677	Last Post by rodw 15 Jul 2026 11:11
qtDragon: Auto Return to Manual Mode After an MDI Command so MPG works Category: Qtvcp Topic started 25 Feb 2026 05:05, by Paul_W Last Post 15 Jul 2026 11:03 by rodw	Replies:8 Views:1352	Last Post by rodw 15 Jul 2026 11:03
Parallel port access is not allowed Category: Installing LinuxCNC Topic started 07 Jul 2026 15:14, by aaron Last Post 15 Jul 2026 08:03 by aaron	Replies:5 Views:1075	aaron Last Post by aaron 15 Jul 2026 08:03
Recommended way to implement spindle enable conditions? Category: HAL Topic started 10 Jul 2026 11:26, by TripleM Last Post 15 Jul 2026 07:41 by TripleM	Replies:5 Views:799	TripleM Last Post by TripleM 15 Jul 2026 07:41
linking U axis to X Category: Advanced Configuration Topic started 11 Jul 2026 20:27, by foam man Last Post 14 Jul 2026 13:53 by tommylight	Replies:4 Views:457	Last Post by tommylight 14 Jul 2026 13:53
Probe Basic widgets missing Category: QtPyVCP Topic started 13 Jul 2026 19:18, by Ismacr63 Last Post 14 Jul 2026 07:51 by Ismacr63	Replies:4 Views:352	Ismacr63 Last Post by Ismacr63 14 Jul 2026 07:51
calling all probe basic lathe users! Category: QtPyVCP Topic started 22 Jun 2026 19:44, by Lcvette Last Post 14 Jul 2026 07:47 by Ismacr63 1 2	Replies:15 Views:1873	Ismacr63 Last Post by Ismacr63 14 Jul 2026 07:47
Every time I boot LinuxCNC, the Xg54 position reading increase 256 Category: General LinuxCNC Questions Topic started 11 Jul 2026 07:17, by xin Last Post 13 Jul 2026 21:43 by onceloved	Replies:2 Views:358	Last Post by onceloved 13 Jul 2026 21:43
Ethernet connection to Mesa 7i76e disconnecting on its own after one minute Category: Plasmac Topic started 25 May 2026 21:14, by RMJ fabrication Last Post 13 Jul 2026 19:09 by PCW 1 2 3 ... 6	Replies:51 Views:4253	Last Post by PCW 13 Jul 2026 19:09
manual tool change with tool length probe Category: G&M Codes Topic started 25 Apr 2025 21:11, by pgf Last Post 13 Jul 2026 17:05 by tuxcnc	Replies:9 Views:2173	tuxcnc Last Post by tuxcnc 13 Jul 2026 17:05
C axis milling cycles. Anyone written any? Category: General LinuxCNC Questions Topic started 09 Jul 2026 23:17, by M4MazakUser Last Post 13 Jul 2026 13:36 by spumco	Replies:3 Views:509	spumco Last Post by spumco 13 Jul 2026 13:36
Adding EtherCAT to LCNC 2.9.2 Category: EtherCAT Topic started 09 Jul 2026 21:32, by HempenHomespun Last Post 13 Jul 2026 10:48 by rodw	Replies:3 Views:580	Last Post by rodw 13 Jul 2026 10:48
Seeking Guidance on Mitsubishi MR-J3 Serial Encoder Protocol (J-A22/J-A24) for M Category: General LinuxCNC Questions Topic started 11 Jul 2026 12:03, by vanlap02 Last Post 12 Jul 2026 22:11 by dm17ry	Replies:3 Views:366	Last Post by dm17ry 12 Jul 2026 22:11
STM32 ST-LINK Utility will not connect to the target. Category: Computers and Hardware Topic started 11 Jul 2026 16:52, by hupernikao23 Last Post 12 Jul 2026 16:23 by tuxcnc	Replies:3 Views:405	tuxcnc Last Post by tuxcnc 12 Jul 2026 16:23
can not jog axis in Gmoccapy Category: Gmoccapy Topic started 03 Jul 2026 19:16, by Etced Last Post 10 Jul 2026 14:21 by Etced 1 2	Replies:12 Views:1606	Etced Last Post by Etced 10 Jul 2026 14:21