Recent Topics (153 topics)

Subject	Replies / Views	Last Post

IgH 1.6.9 MEASURE_TIMING 1 kHz on Debian 13 RT, J6413, I226-V + ec_igc (isolcpus Category: EtherCAT Topic started 28 Aug 2026 08:20, by tietouwa Last Post 28 Aug 2026 08:20 by tietouwa	Replies:0 Views:5	tietouwa Last Post by tietouwa 28 Aug 2026 08:20
Help needed: Software setup for 4-axis tangential stone cutter (Mesa) Category: Advanced Configuration Topic started 27 Aug 2026 20:05, by souh-hil Last Post 28 Aug 2026 05:21 by rodw	Replies:5 Views:87	Last Post by rodw 28 Aug 2026 05:21
Hello everyone Category: General LinuxCNC Questions Topic started 27 Aug 2026 18:47, by yop32 Last Post 28 Aug 2026 05:05 by rodw	Replies:2 Views:46	Last Post by rodw 28 Aug 2026 05:05
Probe Basic - HAL pins not being created Category: QtPyVCP Topic started 28 Aug 2026 03:24, by spumco Last Post 28 Aug 2026 03:24 by spumco	Replies:0 Views:29	spumco Last Post by spumco 28 Aug 2026 03:24
LinuxCNC Meetup Stuttgart 2026 Category: Deutsch Topic started 27 Aug 2026 12:58, by rene-dev Last Post 27 Aug 2026 20:52 by tommylight	Replies:1 Views:71	Last Post by tommylight 27 Aug 2026 20:52
Encoder question Category: Computers and Hardware Topic started 27 Aug 2026 15:51, by Tinker Last Post 27 Aug 2026 20:31 by PCW	Replies:7 Views:102	Last Post by PCW 27 Aug 2026 20:31
Xilinx Zynq 7010 fpga crypto windfall boards Category: Driver Boards Topic started 17 Jun 2025 00:09, by DMNZ Last Post 27 Aug 2026 15:12 by murdemon 1 2 3 ... 7	Replies:65 Views:8449	murdemon Last Post by murdemon 27 Aug 2026 15:12
LinuxCNC-RIO - RealtimeIO for LinuxCNC based on FPGA (ICE40 / ECP5) Category: Computers and Hardware Topic started 18 May 2023 13:30, by meister Last Post 27 Aug 2026 14:03 by meister 1 2 3 ... 104	Replies:1037 Views:239k	meister Last Post by meister 27 Aug 2026 14:03
Probe Basic - user tabs/buttons/etc not appearing Category: QtPyVCP Topic started 23 Aug 2026 16:34, by spumco Last Post 27 Aug 2026 14:01 by Lcvette	Replies:6 Views:202	Last Post by Lcvette 27 Aug 2026 14:01
Making a GUI for Aligning Feeder Positions and Saving the Values to a CSV file Category: Pick and Place Topic started 14 Aug 2022 15:23, by my1987toyota Last Post 27 Aug 2026 09:34 by my1987toyota 1 2	Replies:11 Views:15.6k	Last Post by my1987toyota 27 Aug 2026 09:34
Controller recommendations (other than mesa) Category: Driver Boards Topic started 23 Feb 2020 16:09, by neowalla Last Post 27 Aug 2026 09:14 by timo 1 2 3	Replies:21 Views:6405	timo Last Post by timo 27 Aug 2026 09:14
XHC Handrad - Fehler Category: Deutsch Topic started 27 Aug 2026 08:54, by ErwinCNC Last Post 27 Aug 2026 08:54 by ErwinCNC	Replies:0 Views:57	ErwinCNC Last Post by ErwinCNC 27 Aug 2026 08:54
Ethercat drive configuration woes Category: EtherCAT Topic started 01 Dec 2022 21:08, by mwc Last Post 26 Aug 2026 22:56 by mwc 1 2 3 ... 9	Replies:80 Views:24.7k	mwc Last Post by mwc 26 Aug 2026 22:56
A handy browser-based tool for aligning and assembling STL files: STL Assembly Category: Show Your Stuff Topic started 24 Aug 2026 09:31, by emresensoy Last Post 26 Aug 2026 20:11 by Waldemar	Replies:1 Views:155	Last Post by Waldemar 26 Aug 2026 20:11
Delta ASDA-E3 + IgH – occasional one-cycle position update skip Category: EtherCAT Topic started 26 Aug 2026 15:39, by ajanfahri Last Post 26 Aug 2026 15:39 by ajanfahri	Replies:0 Views:83	Last Post by ajanfahri 26 Aug 2026 15:39
Help needed! Z changes after touching the metal, to a value above the limits. Category: General LinuxCNC Questions Topic started 26 Aug 2026 09:36, by GennadijSpb Last Post 26 Aug 2026 09:36 by GennadijSpb	Replies:0 Views:123	GennadijSpb Last Post by GennadijSpb 26 Aug 2026 09:36
GrooveCam Category: Show Your Stuff Topic started 26 Aug 2026 09:32, by Waldemar Last Post 26 Aug 2026 09:32 by Waldemar	Replies:0 Views:97	Last Post by Waldemar 26 Aug 2026 09:32
Error in tool_offsetview.py Category: Qtvcp Topic started 06 Jan 2022 20:33, by MarkoPolo Last Post 26 Aug 2026 08:39 by MarkoPolo 1 2 3 ... 41	Replies:408 Views:105k	MarkoPolo Last Post by MarkoPolo 26 Aug 2026 08:39
Hydraulic press brake control Category: CNC Machines Topic started 21 Sep 2018 15:40, by microsprintbuilder Last Post 25 Aug 2026 20:10 by think_j 1 2 3 4	Replies:34 Views:17k	think_j Last Post by think_j 25 Aug 2026 20:10
7i95T PktUART: no usable TX output with either official bitfile Category: Driver Boards Topic started 24 Aug 2026 21:13, by Otatiaro Last Post 25 Aug 2026 18:36 by PCW	Replies:7 Views:129	Last Post by PCW 25 Aug 2026 18:36