Recent Topics (295 topics)

Subject	Replies / Views	Last Post

motor-0-position error beim Abbremsen aus 4-7,5 m/min Category: Deutsch Topic started 25 Jan 2025 13:22, by Muftijaja Last Post 30 Apr 2025 17:55 by Muftijaja 1 2 3 4	Replies:30 Views:1317	Muftijaja Last Post by Muftijaja 30 Apr 2025 17:55
Lathe project Category: Turning Topic started 04 Jan 2025 04:24, by Jdolecki Last Post 30 Apr 2025 16:08 by langdons 1 2	Replies:17 Views:1247	langdons Last Post by langdons 30 Apr 2025 16:08
Installation 2.9.4 Debian Bookworm Preempt-RT ISO // Probleme Category: Deutsch Topic started 02 Mar 2025 21:19, by FraesPaul Last Post 30 Apr 2025 15:38 by liutas4x4 1 2	Replies:10 Views:627	liutas4x4 Last Post by liutas4x4 30 Apr 2025 15:38
AC Servo tuning - Joint 0 following error at high velocities Category: Basic Configuration Topic started 28 Apr 2025 13:05, by abi9624 Last Post 30 Apr 2025 14:49 by PCW	Replies:4 Views:211	Last Post by PCW 30 Apr 2025 14:49
EtherCAT + 7i96s + Internet Success Category: EtherCAT Topic started 29 Apr 2025 16:24, by santy Last Post 30 Apr 2025 13:41 by langdons	Replies:4 Views:203	langdons Last Post by langdons 30 Apr 2025 13:41
Updating pncconf for 7i95t Category: Configuration Tools Topic started 13 Apr 2025 00:13, by bigmactx Last Post 30 Apr 2025 13:16 by alexandrap	Replies:4 Views:549	alexandrap Last Post by alexandrap 30 Apr 2025 13:16
Frustrated - cant figure out how to display encoder speed on any gui for lathe Category: Gmoccapy Topic started 29 Apr 2025 21:19, by ffffrf Last Post 29 Apr 2025 23:22 by ffffrf	Replies:2 Views:157	ffffrf Last Post by ffffrf 29 Apr 2025 23:22
Remora - Rpi Software Stepping Using External Microcontroller via SPI Category: Computers and Hardware Topic started 16 Apr 2021 18:06, by Bari Last Post 29 Apr 2025 21:58 by cakeslob 1 2 3 ... 86	Replies:854 Views:191k	cakeslob Last Post by cakeslob 29 Apr 2025 21:58
Developing a Raspberry Pi Pico-based I/O Board for LinuxCNC Category: General LinuxCNC Questions Topic started 13 Mar 2025 11:10, by atrex77 Last Post 29 Apr 2025 19:25 by atrex77 1 2	Replies:15 Views:1119	Last Post by atrex77 29 Apr 2025 19:25
"From scraps were ye made, and scraps ye shall be!" Category: Show Your Stuff Topic started 29 Apr 2025 11:57, by pgf Last Post 29 Apr 2025 15:28 by pgf	Replies:2 Views:170	pgf Last Post by pgf 29 Apr 2025 15:28
Tandem Y Axis in stepconf assistance. Category: StepConf Wizard Topic started 27 Apr 2025 00:55, by Mother Canucker Last Post 29 Apr 2025 14:57 by Mother Canucker 1 2	Replies:11 Views:453	Mother Canucker Last Post by Mother Canucker 29 Apr 2025 14:57
EtherCAT and selfmade driver Category: EtherCAT Topic started 29 Apr 2025 07:11, by Neiji_msk Last Post 29 Apr 2025 13:58 by Hakan	Replies:3 Views:180	Hakan Last Post by Hakan 29 Apr 2025 13:58
Z axis is being controlled by A Category: Basic Configuration Topic started 27 Apr 2025 21:26, by dannym Last Post 29 Apr 2025 12:45 by langdons 1 2	Replies:11 Views:534	langdons Last Post by langdons 29 Apr 2025 12:45
First time to try build my xml for not listed ethercat in-out component Category: EtherCAT Topic started 18 Apr 2025 16:44, by bkt Last Post 29 Apr 2025 08:34 by Hakan 1 2 3	Replies:22 Views:1074	Hakan Last Post by Hakan 29 Apr 2025 08:34
Gmoccapy G54 Offsets Category: Gmoccapy Topic started 27 Apr 2025 03:05, by electrosteam Last Post 29 Apr 2025 06:40 by Aciera	Replies:8 Views:227	Last Post by Aciera 29 Apr 2025 06:40
HSMworks Alternative? Category: CAD CAM Topic started 26 Apr 2025 02:21, by Centurykid Last Post 28 Apr 2025 21:00 by langdons	Replies:1 Views:202	langdons Last Post by langdons 28 Apr 2025 21:00
QtDragon_hd + Basic Probe - probing results not displayed Category: Qtvcp Topic started 06 Apr 2025 11:50, by AMLD Last Post 28 Apr 2025 20:02 by cmorley	Replies:6 Views:411	cmorley Last Post by cmorley 28 Apr 2025 20:02
Issue with OP Entry Delay and Failures in LinuxCNC + EtherCAT System Category: EtherCAT Topic started 04 Mar 2025 09:39, by shaying526 Last Post 28 Apr 2025 18:48 by papagno-source 1 2	Replies:18 Views:1216	papagno-source Last Post by papagno-source 28 Apr 2025 18:48
joint 0 following error Category: General LinuxCNC Questions Topic started 20 Apr 2022 18:20, by diep Last Post 28 Apr 2025 14:55 by tommylight 1 2	Replies:10 Views:1867	Last Post by tommylight 28 Apr 2025 14:55
Mesa CT 2.1.7 and Mesa 7I97T setup running Gmoccapy Category: Configuration Tools Topic started 23 Apr 2025 08:13, by H-S-W Last Post 28 Apr 2025 12:13 by JT	Replies:3 Views:244	Last Post by JT 28 Apr 2025 12:13