Plasmac 671 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Mesa Hardware Recommendations Topic started 27 Jun 2020 19:25, by KaleD Last Post 28 Jun 2020 22:18 by KaleD 1 2	Replies:13 Views:2227	KaleD Last Post by KaleD 28 Jun 2020 22:18
7I96 Plasmac THAC / encoder config question Topic started 27 Jun 2020 21:53, by calvin.d Last Post 28 Jun 2020 00:43 by calvin.d 1 2	Replies:10 Views:2204	calvin.d Last Post by calvin.d 28 Jun 2020 00:43
THC input pins Topic started 27 Jun 2020 04:10, by KaleD Last Post 27 Jun 2020 05:06 by phillc54	Replies:1 Views:774	Last Post by phillc54 27 Jun 2020 05:06
Raspberry Pi4 Hal configuration for torch on Topic started 24 Jun 2020 11:43, by greekart Last Post 26 Jun 2020 09:35 by greekart 1 2	Replies:11 Views:2441	Last Post by greekart 26 Jun 2020 09:35
THC not showing on screen Topic started 17 Jun 2020 23:35, by Nate Last Post 25 Jun 2020 11:46 by tommylight 1 2	Replies:14 Views:2457	Last Post by tommylight 25 Jun 2020 11:46
setting up thcad Topic started 29 May 2020 00:56, by Aaron3309 Last Post 25 Jun 2020 02:05 by PCW 1 2 3 4	Replies:36 Views:4743	Last Post by PCW 25 Jun 2020 02:05
I don't have an Arc OK Topic started 23 Jun 2020 03:41, by KaleD Last Post 24 Jun 2020 14:24 by KaleD 1 2	Replies:15 Views:3131	KaleD Last Post by KaleD 24 Jun 2020 14:24
Probe or Arc problem Topic started 24 Jun 2020 03:06, by KaleD Last Post 24 Jun 2020 04:43 by phillc54	Replies:1 Views:681	Last Post by phillc54 24 Jun 2020 04:43
PlasmaC questions new setup Topic started 22 May 2020 18:13, by Clive S Last Post 23 Jun 2020 07:24 by Clive S 1 2 3 ... 14	Replies:133 Views:14k	Clive S Last Post by Clive S 23 Jun 2020 07:24
Z axis height at end of cut Topic started 11 Jun 2020 21:35, by rodw Last Post 22 Jun 2020 20:48 by tommylight 1 2 3 ... 5	Replies:49 Views:6055	Last Post by tommylight 22 Jun 2020 20:48
Probe Z trouble Topic started 18 Jun 2020 04:41, by KaleD Last Post 20 Jun 2020 23:33 by phillc54	Replies:5 Views:951	Last Post by phillc54 20 Jun 2020 23:33
plasmac install error Topic started 30 May 2020 00:09, by Nate Last Post 16 Jun 2020 12:07 by tommylight 1 2	Replies:16 Views:2823	Last Post by tommylight 16 Jun 2020 12:07
Feature update required. Topic started 13 Jun 2020 22:19, by rodw Last Post 16 Jun 2020 02:08 by phillc54 1 2 3	Replies:26 Views:3162	Last Post by phillc54 16 Jun 2020 02:08
Float Switch Activated Topic started 14 Jun 2020 12:21, by little_sparky Last Post 16 Jun 2020 01:53 by phillc54	Replies:6 Views:973	Last Post by phillc54 16 Jun 2020 01:53
Watchdog has bit! Topic started 13 Jun 2020 04:28, by little_sparky Last Post 14 Jun 2020 12:48 by PCW 1 2	Replies:19 Views:3085	Last Post by PCW 14 Jun 2020 12:48
using Sheetcam and PlasmaC re Kerf Topic started 13 Jun 2020 17:56, by Clive S Last Post 14 Jun 2020 08:26 by phillc54 1 2	Replies:12 Views:2317	Last Post by phillc54 14 Jun 2020 08:26
Running CNC Plasma off generator Topic started 09 Jun 2020 07:42, by little_sparky Last Post 10 Jun 2020 12:14 by bbsr_5a 1 2	Replies:14 Views:2783	bbsr_5a Last Post by bbsr_5a 10 Jun 2020 12:14
THCAD-10 Jumper Settings Topic started 09 Jun 2020 07:35, by little_sparky Last Post 09 Jun 2020 07:43 by little_sparky	Replies:2 Views:684	little_sparky Last Post by little_sparky 09 Jun 2020 07:43
2.8 or 2.9 Topic started 08 Jun 2020 14:23, by KaleD Last Post 08 Jun 2020 23:07 by phillc54	Replies:4 Views:936	Last Post by phillc54 08 Jun 2020 23:07
Plasmac Configurator Topic started 07 Jun 2020 22:21, by KaleD Last Post 08 Jun 2020 14:09 by KaleD 1 2 3	Replies:23 Views:2973	KaleD Last Post by KaleD 08 Jun 2020 14:09

Time to create page: 0.111 seconds