Plasmac 739 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Using Spotting with Sheetcam Topic started 21 Jul 2020 18:39, by Clive S Last Post 23 Jul 2020 12:25 by phillc54 1 2 3 4	Replies:34 Views:5608	Last Post by phillc54 23 Jul 2020 12:25
Error Recovery Topic started 18 Jun 2020 07:16, by phillc54 Last Post 23 Jul 2020 12:21 by tommylight 1 2 3 ... 10	Replies:92 Views:12.3k	Last Post by tommylight 23 Jul 2020 12:21
Ohmic Enable Check Box Topic started 22 Jul 2020 21:34, by snowgoer540 Last Post 23 Jul 2020 10:14 by snowgoer540 1 2	Replies:10 Views:2866	Last Post by snowgoer540 23 Jul 2020 10:14
i cant open plasmac from Sample Configurations > by_machine > plasmac Topic started 21 Jul 2020 00:20, by Himarc3D Last Post 22 Jul 2020 02:22 by phillc54	Replies:3 Views:1134	Last Post by phillc54 22 Jul 2020 02:22
Plamsac air scribe set up Topic started 19 Jul 2020 03:35, by CBEAR Last Post 21 Jul 2020 10:23 by snowgoer540 1 2	Replies:18 Views:3632	Last Post by snowgoer540 21 Jul 2020 10:23
Unknown m code used: M190 Topic started 21 Jul 2020 05:41, by CFE Last Post 21 Jul 2020 06:53 by phillc54	Replies:7 Views:1608	Last Post by phillc54 21 Jul 2020 06:53
Upgrade problems Topic started 13 Jul 2020 23:39, by CFE Last Post 20 Jul 2020 12:36 by tommylight 1 2	Replies:19 Views:3014	Last Post by tommylight 20 Jul 2020 12:36
New Configuration Error Topic started 12 Jul 2020 19:31, by snowgoer540 Last Post 20 Jul 2020 12:29 by Clive S 1 2 3 ... 5	Replies:40 Views:6821	Clive S Last Post by Clive S 20 Jul 2020 12:29
Cant find plasmac to configure Topic started 17 Jul 2020 23:11, by kramerda Last Post 17 Jul 2020 23:52 by phillc54	Replies:5 Views:917	Last Post by phillc54 17 Jul 2020 23:52
Steppers or DC motor for Z axis THC Topic started 16 Jul 2020 13:36, by kramerda Last Post 16 Jul 2020 16:28 by tommylight	Replies:3 Views:1184	Last Post by tommylight 16 Jul 2020 16:28
Torch Breakaway and Torch Pulse Topic started 13 Jul 2020 18:32, by snowgoer540 Last Post 16 Jul 2020 12:02 by snowgoer540 1 2 3 ... 5	Replies:41 Views:6030	Last Post by snowgoer540 16 Jul 2020 12:02
Plasma no ARC OK and torch fires when machine is turned on Topic started 13 Jul 2020 05:06, by luftlupus Last Post 16 Jul 2020 01:32 by luftlupus 1 2 3	Replies:22 Views:4360	Last Post by luftlupus 16 Jul 2020 01:32
THCAD-300 Jumper Topic started 10 Jul 2020 18:24, by KaleD Last Post 11 Jul 2020 11:00 by tommylight	Replies:7 Views:2781	Last Post by tommylight 11 Jul 2020 11:00
Materialverter Topic started 06 Jul 2020 22:26, by snowgoer540 Last Post 08 Jul 2020 00:38 by snowgoer540 1 2 3	Replies:25 Views:4332	Last Post by snowgoer540 08 Jul 2020 00:38
HAL Question Topic started 01 Jul 2020 22:02, by snowgoer540 Last Post 04 Jul 2020 02:11 by rodw 1 2 3 ... 5	Replies:47 Views:7104	Last Post by rodw 04 Jul 2020 02:11
Axis Window Layout Topic started 15 May 2020 05:19, by phillc54 Last Post 04 Jul 2020 00:04 by snowgoer540	Replies:6 Views:1392	Last Post by snowgoer540 04 Jul 2020 00:04
cut quality question Topic started 03 Jul 2020 20:21, by motal2004 Last Post 03 Jul 2020 20:42 by tommylight	Replies:1 Views:977	Last Post by tommylight 03 Jul 2020 20:42
Using Powermax with RS485 Topic started 24 Jun 2020 08:37, by Clive S Last Post 29 Jun 2020 23:30 by phillc54 1 2 3	Replies:29 Views:4186	Last Post by phillc54 29 Jun 2020 23:30
Mesa Hardware Recommendations Topic started 27 Jun 2020 19:25, by KaleD Last Post 28 Jun 2020 22:18 by KaleD 1 2	Replies:13 Views:3044	KaleD Last Post by KaleD 28 Jun 2020 22:18
7I96 Plasmac THAC / encoder config question Topic started 27 Jun 2020 21:53, by calvin.d Last Post 28 Jun 2020 00:43 by calvin.d 1 2	Replies:10 Views:3013	calvin.d Last Post by calvin.d 28 Jun 2020 00:43

Time to create page: 0.306 seconds