Basic Configuration 1297 topics

A place to discuss basic configurations like probe input, homing etc.

Subject	Replies / Views	Last Post
How start Config Yaskawa Servo Topic started 06 May 2015 02:13, by aer73 Last Post 14 Jun 2015 11:27 by aer73 1 2	Replies:15 Views:7926	aer73 Last Post by aer73 14 Jun 2015 11:27
HSMXpress to LinuxCNC tool table conversion script Topic started 09 Jun 2015 12:18, by adam3999 Last Post 12 Jun 2015 03:37 by andypugh	Replies:1 Views:1791	Last Post by andypugh 12 Jun 2015 03:37
LInuxCNC with Nema34's, DM860A and BF20 Mill Topic started 10 Jun 2015 07:58, by speedracer Last Post 11 Jun 2015 17:03 by speedracer	Replies:6 Views:4732	speedracer Last Post by speedracer 11 Jun 2015 17:03
recovering from a on limit error? Topic started 05 Jun 2015 20:26, by rotccapt Last Post 07 Jun 2015 23:10 by rotccapt 1 2	Replies:12 Views:5722	rotccapt Last Post by rotccapt 07 Jun 2015 23:10
Configure XY scale with belts Topic started 29 May 2015 17:32, by nerdegutta Last Post 30 May 2015 19:24 by nerdegutta	Replies:4 Views:2405	nerdegutta Last Post by nerdegutta 30 May 2015 19:24
Strange Offsett in Y and Z axis after touchoff Topic started 12 May 2015 14:13, by REEEN Last Post 18 May 2015 22:31 by andypugh	Replies:8 Views:1771	Last Post by andypugh 18 May 2015 22:31
halrun Topic started 16 May 2015 02:20, by pmcstoneinc Last Post 16 May 2015 23:09 by PCW	Replies:1 Views:1991	Last Post by PCW 16 May 2015 23:09
gmoccapy startup error Topic started 23 Mar 2015 19:35, by brosskgm Last Post 05 May 2015 05:17 by backwoodsjack	Replies:2 Views:1916	backwoodsjack Last Post by backwoodsjack 05 May 2015 05:17
difference PWMGEN fwd / rev Topic started 01 May 2015 23:34, by mpvriens Last Post 01 May 2015 23:48 by PCW	Replies:1 Views:1379	Last Post by PCW 01 May 2015 23:48
TN6560 variant - homing issues. Topic started 28 Apr 2015 23:43, by dchurch24 Last Post 01 May 2015 18:57 by andypugh	Replies:5 Views:1722	Last Post by andypugh 01 May 2015 18:57
Home all with A Topic started 30 Apr 2015 02:51, by cwebs Last Post 30 Apr 2015 21:13 by cwebs	Replies:6 Views:1597	cwebs Last Post by cwebs 30 Apr 2015 21:13
Reading non-trivial joint values Topic started 15 Mar 2015 15:34, by subtractive Last Post 27 Apr 2015 18:42 by andypugh	Replies:6 Views:1578	Last Post by andypugh 27 Apr 2015 18:42
How to change default Jog speed Topic started 26 Apr 2015 02:48, by cwebs Last Post 26 Apr 2015 17:45 by cwebs	Replies:2 Views:4332	cwebs Last Post by cwebs 26 Apr 2015 17:45
No Gentrivkins module Topic started 22 Apr 2015 16:46, by KenC Last Post 25 Apr 2015 08:53 by KenC 1 2 3	Replies:24 Views:5750	KenC Last Post by KenC 25 Apr 2015 08:53
XYUV hotwire machine - axis visualisation wrong Topic started 21 Apr 2015 08:58, by chris_gough Last Post 23 Apr 2015 22:02 by andypugh	Replies:3 Views:2033	Last Post by andypugh 23 Apr 2015 22:02
Base Thread speed Topic started 21 Apr 2015 09:46, by jbunch Last Post 22 Apr 2015 09:06 by PCW	Replies:8 Views:4331	Last Post by PCW 22 Apr 2015 09:06
TB6560AHQ locks steppers when power applied. Topic started 05 Apr 2015 01:40, by richard5008 Last Post 07 Apr 2015 22:56 by andypugh	Replies:9 Views:2001	Last Post by andypugh 07 Apr 2015 22:56
TB6560 Homing switches not triggering. Go Without? Topic started 30 Mar 2015 22:31, by JOguino Last Post 31 Mar 2015 07:53 by andypugh	Replies:2 Views:2247	Last Post by andypugh 31 Mar 2015 07:53
stepconf setup Topic started 28 Mar 2015 02:45, by johnl2 Last Post 30 Mar 2015 02:04 by johnl2 1 2	Replies:16 Views:4418	johnl2 Last Post by johnl2 30 Mar 2015 02:04
axis x homing and g54x0 from program Topic started 18 Mar 2015 14:01, by albova Last Post 18 Mar 2015 18:49 by albova	Replies:2 Views:1291	albova Last Post by albova 18 Mar 2015 18:49

Time to create page: 0.171 seconds