PnCConf Wizard 771 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
7i77D single ended encoder connections Topic started 15 Sep 2022 05:30, by msrdiesel Last Post 16 Sep 2022 02:19 by msrdiesel	Replies:3 Views:345	Last Post by msrdiesel 16 Sep 2022 02:19
Re:5i20 + 7i52s + 7i37TA -> change the IO Pins Topic started 06 Sep 2012 20:40, by trilobyte Last Post 15 Sep 2022 13:04 by BeWerk 1 2 3 ... 5	Replies:44 Views:24.7k	BeWerk Last Post by BeWerk 15 Sep 2022 13:04
HowTo: MESA Ethernet Board Network Config Using systemd Topic started 13 Sep 2022 13:56, by fletch Last Post 13 Sep 2022 16:05 by tommylight	Replies:3 Views:344	Last Post by tommylight 13 Sep 2022 16:05
After switch to Mesa 6i25 (5i25), home switches not recognized. [Mis-configured] Topic started 11 Sep 2022 20:27, by clunc Last Post 13 Sep 2022 02:28 by clunc	Replies:8 Views:523	Last Post by clunc 13 Sep 2022 02:28
Error unable to launch after pncconf. Topic started 30 Aug 2022 00:18, by RobKin Last Post 06 Sep 2022 15:36 by tommylight 1 2	Replies:13 Views:1224	Last Post by tommylight 06 Sep 2022 15:36
How do PnCConf's Mesa Card 0 I/O tabs' pin numbers correspond to stepconf's? Topic started 28 Jul 2022 14:09, by clunc Last Post 06 Sep 2022 10:14 by clunc 1 2	Replies:15 Views:1644	Last Post by clunc 06 Sep 2022 10:14
7i96s: can't seem to get a stepper enable signal Topic started 03 Sep 2022 17:21, by Dr. John Last Post 04 Sep 2022 01:51 by PCW 1 2	Replies:14 Views:902	Last Post by PCW 04 Sep 2022 01:51
[YES]Is there a way to create/generate firmware .xml from an existing .pin file? Topic started 22 Jul 2022 08:10, by clunc Last Post 30 Aug 2022 18:17 by Andreas_Rackow	Replies:8 Views:714	Andreas_Rackow Last Post by Andreas_Rackow 30 Aug 2022 18:17
Ini file is overwritten Topic started 22 Aug 2022 16:45, by vkhargwanshi Last Post 23 Aug 2022 11:22 by JT	Replies:3 Views:418	Last Post by JT 23 Aug 2022 11:22
Stepgen spindle Topic started 13 Aug 2022 12:21, by gilesclement Last Post 18 Aug 2022 13:52 by PCW	Replies:8 Views:619	Last Post by PCW 18 Aug 2022 13:52
MPG working with joint but not with axis ??? [solved] Topic started 15 Aug 2022 07:39, by JPL Last Post 18 Aug 2022 06:23 by sprintertrd 1 2	Replies:14 Views:1323	sprintertrd Last Post by sprintertrd 18 Aug 2022 06:23
PNC config error Topic started 14 Aug 2022 13:09, by rajsekhar Last Post 15 Aug 2022 16:16 by rajsekhar	Replies:8 Views:447	rajsekhar Last Post by rajsekhar 15 Aug 2022 16:16
Cycle start/resume pause and external buttons problem (Mesa 7i76e card) Topic started 01 Aug 2022 08:06, by raychar Last Post 04 Aug 2022 15:03 by raychar 1 2	Replies:13 Views:1128	raychar Last Post by raychar 04 Aug 2022 15:03
All GPIO pins not shown by PnCConf for 7i96s Topic started 26 Jul 2022 09:08, by vkhargwanshi Last Post 03 Aug 2022 02:04 by vkhargwanshi 1 2	Replies:17 Views:1648	vkhargwanshi Last Post by vkhargwanshi 03 Aug 2022 02:04
Re: the sticky: "5i25 firmware XML files for pncconf" (missing newer files) Topic started 22 Jul 2022 08:02, by clunc Last Post 23 Jul 2022 01:29 by cmorley	Replies:1 Views:344	cmorley Last Post by cmorley 23 Jul 2022 01:29
ISE Project Navigator 14.7 Topic started 21 Jul 2022 08:34, by Manja Last Post 21 Jul 2022 14:12 by PCW	Replies:1 Views:441	Last Post by PCW 21 Jul 2022 14:12
My first steps with LinuxCNC - comments appreciated :) Using Mesa 7i80 and 7i78 Topic started 13 Jul 2022 22:27, by sukandar Last Post 21 Jul 2022 03:49 by PCW 1 2	Replies:13 Views:1061	Last Post by PCW 21 Jul 2022 03:49
PncConfig Errno 13 during setup Topic started 11 Jul 2022 14:21, by gilesclement Last Post 11 Jul 2022 17:19 by tommylight	Replies:2 Views:367	Last Post by tommylight 11 Jul 2022 17:19
Error running LinuxCNC after setting up with Pncconf Topic started 09 Jul 2022 16:19, by mloser Last Post 09 Jul 2022 16:25 by tommylight	Replies:1 Views:328	Last Post by tommylight 09 Jul 2022 16:25
LinuxCNC 2.8 - PNCconf bug - bad arrow Topic started 06 Jul 2022 14:52, by zz912 Last Post 07 Jul 2022 15:35 by zz912	Replies:3 Views:409	Last Post by zz912 07 Jul 2022 15:35

Time to create page: 0.201 seconds