PnCConf Wizard 874 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
Maxvel is too big error and stepper settings ques. Topic started 04 May 2016 12:54, by ommar Last Post 04 May 2016 15:15 by PCW	Replies:2 Views:2988	Last Post by PCW 04 May 2016 15:15
Jog speed is very slow Topic started 11 Mar 2016 17:45, by Clive S Last Post 01 May 2016 10:11 by epineh 1 2	Replies:12 Views:6184	epineh Last Post by epineh 01 May 2016 10:11
Mesa 6i25 + 7i77 setup help needed Topic started 28 Apr 2016 21:46, by jsskangas Last Post 29 Apr 2016 08:35 by jsskangas	Replies:5 Views:2239	jsskangas Last Post by jsskangas 29 Apr 2016 08:35
Analog Spindle Drive Voltage Problem Topic started 28 Apr 2016 01:45, by Sousanator Last Post 28 Apr 2016 22:58 by PCW	Replies:4 Views:1661	Last Post by PCW 28 Apr 2016 22:58
7i43 BITFILE issue for UART TX Topic started 14 Apr 2016 23:09, by gandalf Last Post 28 Apr 2016 09:47 by andypugh	Replies:7 Views:1749	Last Post by andypugh 28 Apr 2016 09:47
Test Axis fails to start Topic started 21 Apr 2016 17:09, by gandalf Last Post 22 Apr 2016 08:14 by Amedee	Replies:1 Views:1609	Last Post by Amedee 22 Apr 2016 08:14
PnCConf Setup issue with the Spindle Topic started 13 Apr 2016 21:35, by twender Last Post 19 Apr 2016 13:33 by twender 1 2	Replies:18 Views:7523	Last Post by twender 19 Apr 2016 13:33
tried pncconf and get these errors - attached Topic started 15 Apr 2016 23:23, by Alicee Last Post 16 Apr 2016 16:56 by cncbasher	Replies:3 Views:1978	cncbasher Last Post by cncbasher 16 Apr 2016 16:56
What should I answer to PNCconf for XYZA steppers Topic started 14 Apr 2016 14:44, by Alicee Last Post 14 Apr 2016 16:43 by Alicee	Replies:2 Views:1744	Last Post by Alicee 14 Apr 2016 16:43
servo period setup Topic started 11 Apr 2016 19:29, by gandalf Last Post 11 Apr 2016 20:17 by PCW	Replies:4 Views:4777	Last Post by PCW 11 Apr 2016 20:17
5i25 with Probotix Unity Controller Problems Topic started 09 Apr 2016 19:47, by Irritant Last Post 10 Apr 2016 02:47 by PCW 1 2	Replies:14 Views:4251	Last Post by PCW 10 Apr 2016 02:47
Config for 5i25 + 2 7i74 error Topic started 08 Apr 2016 13:20, by terkaa Last Post 08 Apr 2016 13:20 by terkaa	Replies:0 Views:1294	terkaa Last Post by terkaa 08 Apr 2016 13:20
Installing and checking firmware on mesa 5125 Topic started 27 Feb 2016 18:15, by Ncmill.ts Last Post 04 Apr 2016 22:39 by PCW 1 2	Replies:17 Views:8352	Last Post by PCW 04 Apr 2016 22:39
7i43 and parallel port errors Topic started 02 Apr 2016 23:46, by gandalf Last Post 04 Apr 2016 19:46 by gandalf	Replies:3 Views:2455	gandalf Last Post by gandalf 04 Apr 2016 19:46
Velocity Won't Exceed 6000mm Topic started 20 Mar 2016 23:26, by THEQYD Last Post 02 Apr 2016 21:21 by andypugh	Replies:4 Views:1440	Last Post by andypugh 02 Apr 2016 21:21
Spindle Motor values Topic started 02 Apr 2016 13:38, by dinodf Last Post 02 Apr 2016 17:23 by cmorley	Replies:1 Views:1551	cmorley Last Post by cmorley 02 Apr 2016 17:23
external controlls screen dissapeard Topic started 01 Apr 2016 18:59, by kagouraki Last Post 02 Apr 2016 08:16 by kagouraki	Replies:2 Views:1146	Last Post by kagouraki 02 Apr 2016 08:16
7i76 Spindle config Topic started 29 Mar 2016 01:03, by eman5oh Last Post 30 Mar 2016 09:13 by andypugh	Replies:4 Views:1610	Last Post by andypugh 30 Mar 2016 09:13
Help needed with Pendant Config Topic started 24 Mar 2016 13:08, by eman5oh Last Post 29 Mar 2016 15:34 by eman5oh	Replies:2 Views:1580	eman5oh Last Post by eman5oh 29 Mar 2016 15:34
Limit and home config errors Topic started 28 Mar 2016 14:55, by eman5oh Last Post 28 Mar 2016 23:57 by eman5oh	Replies:4 Views:1528	eman5oh Last Post by eman5oh 28 Mar 2016 23:57

Time to create page: 0.388 seconds