General LinuxCNC Questions 6170 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Desktop help Topic started 27 Jul 2026 04:33, by nickm1969@live.com Last Post 27 Jul 2026 05:12 by tommylight	Replies:1 Views:306	Last Post by tommylight 27 Jul 2026 05:12
Machine not executing G02 instruction Topic started 25 Jul 2026 22:42, by scsmith1451 Last Post 26 Jul 2026 15:27 by scsmith1451	Replies:5 Views:282	Last Post by scsmith1451 26 Jul 2026 15:27
Replacing RichAuto A11 handle with PC control (LinuxCNC/Mach/UCCNC) on AC servo Topic started 06 Jul 2026 08:57, by usmandeveloper Last Post 25 Jul 2026 03:15 by tommylight	Replies:1 Views:489	Last Post by tommylight 25 Jul 2026 03:15
mesa card 5i25 not being seen by mesaflash after update Topic started 24 Jul 2026 13:02, by bevins Last Post 24 Jul 2026 15:07 by bevins	Replies:6 Views:267	Last Post by bevins 24 Jul 2026 15:07
apt update error: "no longer has a Release file" Topic started 23 Jul 2026 21:09, by dlv Last Post 24 Jul 2026 11:21 by rodw	Replies:2 Views:267	Last Post by rodw 24 Jul 2026 11:21
using linuxcnc on a raspberry pi to control a boxford 250pc lathe Topic started 23 Jul 2026 08:11, by Zipdodar Last Post 24 Jul 2026 08:21 by rodw	Replies:2 Views:234	Last Post by rodw 24 Jul 2026 08:21
linuxcnc frequent freeze Topic started 22 Jul 2026 22:31, by RLA Last Post 23 Jul 2026 21:30 by RLA 1 2	Replies:15 Views:605	RLA Last Post by RLA 23 Jul 2026 21:30
The machine tool coordinate system shifts before and after RTCP is turned on Topic started 20 Jul 2026 11:33, by kanesl Last Post 23 Jul 2026 09:14 by Aciera	Replies:6 Views:384	Last Post by Aciera 23 Jul 2026 09:14
LinuxCNC started in error mode Topic started 19 Jul 2026 02:44, by DMoneyAllstar Last Post 19 Jul 2026 08:21 by rodw	Replies:3 Views:263	Last Post by rodw 19 Jul 2026 08:21
arcs in 4 axis mode Topic started 10 Oct 2022 13:23, by foam man Last Post 17 Jul 2026 14:07 by foam man	Replies:6 Views:1490	foam man Last Post by foam man 17 Jul 2026 14:07
7i97T analog out always -10V Topic started 17 Jul 2026 12:42, by Onkelmat Last Post 17 Jul 2026 12:58 by PCW	Replies:1 Views:232	Last Post by PCW 17 Jul 2026 12:58
running the spindle as a lathe spindle Topic started 15 Jul 2026 17:54, by pgf Last Post 16 Jul 2026 19:09 by MikkelRS	Replies:2 Views:419	Last Post by MikkelRS 16 Jul 2026 19:09
Getting Trixie to play nice Topic started 15 Jul 2026 07:57, by aaron Last Post 15 Jul 2026 12:55 by tuxcnc	Replies:2 Views:377	tuxcnc Last Post by tuxcnc 15 Jul 2026 12:55
Trixy Install problems Topic started 08 Jul 2026 20:47, by aaron Last Post 15 Jul 2026 11:11 by rodw	Replies:8 Views:730	Last Post by rodw 15 Jul 2026 11:11
Every time I boot LinuxCNC, the Xg54 position reading increase 256 Topic started 11 Jul 2026 07:17, by xin Last Post 13 Jul 2026 21:43 by onceloved	Replies:2 Views:401	Last Post by onceloved 13 Jul 2026 21:43
C axis milling cycles. Anyone written any? Topic started 09 Jul 2026 23:17, by M4MazakUser Last Post 13 Jul 2026 13:36 by spumco	Replies:3 Views:554	spumco Last Post by spumco 13 Jul 2026 13:36
Seeking Guidance on Mitsubishi MR-J3 Serial Encoder Protocol (J-A22/J-A24) for M Topic started 11 Jul 2026 12:03, by vanlap02 Last Post 12 Jul 2026 22:11 by dm17ry	Replies:3 Views:426	Last Post by dm17ry 12 Jul 2026 22:11
Homing switch setup in hal Topic started 08 Jul 2026 17:39, by RLA Last Post 09 Jul 2026 21:58 by PCW	Replies:9 Views:519	Last Post by PCW 09 Jul 2026 21:58
Test system setup Topic started 22 Jun 2026 05:45, by pb12 Last Post 09 Jul 2026 12:56 by tommylight	Replies:9 Views:710	Last Post by tommylight 09 Jul 2026 12:56
Is there a public NML/status signal for completion of one EMC_TASK_PLAN_STEP? Topic started 07 Jul 2026 20:16, by rhscdn Last Post 09 Jul 2026 00:37 by rodw	Replies:3 Views:545	Last Post by rodw 09 Jul 2026 00:37

Time to create page: 0.364 seconds