Recent Topics (135 topics)

Subject	Replies / Views	Last Post

Probe Basic widgets missing Category: QtPyVCP Topic started 13 Jul 2026 19:18, by Ismacr63 Last Post 14 Jul 2026 07:51 by Ismacr63	Replies:4 Views:254	Ismacr63 Last Post by Ismacr63 14 Jul 2026 07:51
calling all probe basic lathe users! Category: QtPyVCP Topic started 22 Jun 2026 19:44, by Lcvette Last Post 14 Jul 2026 07:47 by Ismacr63 1 2	Replies:15 Views:1367	Ismacr63 Last Post by Ismacr63 14 Jul 2026 07:47
Every time I boot LinuxCNC, the Xg54 position reading increase 256 Category: General LinuxCNC Questions Topic started 11 Jul 2026 07:17, by xin Last Post 13 Jul 2026 21:43 by onceloved	Replies:2 Views:296	Last Post by onceloved 13 Jul 2026 21:43
Bearing replacement advice for PM-25MV mill (spindle and pulley shaft) Category: Milling Machines Topic started 13 Jul 2026 20:23, by Ismacr63 Last Post 13 Jul 2026 20:23 by Ismacr63	Replies:0 Views:223	Ismacr63 Last Post by Ismacr63 13 Jul 2026 20:23
Ethernet connection to Mesa 7i76e disconnecting on its own after one minute Category: Plasmac Topic started 25 May 2026 21:14, by RMJ fabrication Last Post 13 Jul 2026 19:09 by PCW 1 2 3 ... 6	Replies:51 Views:3455	Last Post by PCW 13 Jul 2026 19:09
Unable to Jog When HAL_ToggleBtn Active Category: General LinuxCNC Questions Topic started 13 Jul 2026 17:54, by scsmith1451 Last Post 13 Jul 2026 17:54 by scsmith1451	Replies:0 Views:165	Last Post by scsmith1451 13 Jul 2026 17:54
manual tool change with tool length probe Category: G&M Codes Topic started 25 Apr 2025 21:11, by pgf Last Post 13 Jul 2026 17:05 by tuxcnc	Replies:9 Views:1825	tuxcnc Last Post by tuxcnc 13 Jul 2026 17:05
C axis milling cycles. Anyone written any? Category: General LinuxCNC Questions Topic started 09 Jul 2026 23:17, by M4MazakUser Last Post 13 Jul 2026 13:36 by spumco	Replies:3 Views:435	spumco Last Post by spumco 13 Jul 2026 13:36
Adding EtherCAT to LCNC 2.9.2 Category: EtherCAT Topic started 09 Jul 2026 21:32, by HempenHomespun Last Post 13 Jul 2026 10:48 by rodw	Replies:3 Views:463	Last Post by rodw 13 Jul 2026 10:48
Seeking Guidance on Mitsubishi MR-J3 Serial Encoder Protocol (J-A22/J-A24) for M Category: General LinuxCNC Questions Topic started 11 Jul 2026 12:03, by vanlap02 Last Post 12 Jul 2026 22:11 by dm17ry	Replies:3 Views:280	Last Post by dm17ry 12 Jul 2026 22:11
Successful Raspberry Pi 4 Trixie LinuxCNC install. Category: Installing LinuxCNC Topic started 12 Jul 2026 19:06, by Rykagon Last Post 12 Jul 2026 19:06 by Rykagon	Replies:0 Views:198	Rykagon Last Post by Rykagon 12 Jul 2026 19:06
STM32 ST-LINK Utility will not connect to the target. Category: Computers and Hardware Topic started 11 Jul 2026 16:52, by hupernikao23 Last Post 12 Jul 2026 16:23 by tuxcnc	Replies:3 Views:311	tuxcnc Last Post by tuxcnc 12 Jul 2026 16:23
FabScan - LinuxCNC Camera-Assisted Tracing / Scanning Project Category: Plasma & Laser Topic started 05 Jul 2026 14:07, by FabLabRacing Last Post 11 Jul 2026 19:14 by FabLabRacing	Replies:3 Views:589	FabLabRacing Last Post by FabLabRacing 11 Jul 2026 19:14
Hurco BMC 30 AP Category: CNC Machines Topic started 28 May 2021 08:10, by 5_Zylinder Last Post 11 Jul 2026 12:13 by Aciera 1 2 3 ... 10	Replies:90 Views:19.3k	Last Post by Aciera 11 Jul 2026 12:13
Flexi-HAL – “hard limits tripped”, home inputs read as permanently triggered Category: Computers and Hardware Topic started 10 Jul 2026 21:46, by HIBA Last Post 10 Jul 2026 21:46 by HIBA	Replies:0 Views:268	HIBA Last Post by HIBA 10 Jul 2026 21:46
VMC Bridgeport 760 22 Retrofit Project Category: CNC Machines Topic started 10 Jul 2026 16:44, by Mafuba Last Post 10 Jul 2026 16:44 by Mafuba	Replies:0 Views:233	Mafuba Last Post by Mafuba 10 Jul 2026 16:44
can not jog axis in Gmoccapy Category: Gmoccapy Topic started 03 Jul 2026 19:16, by Etced Last Post 10 Jul 2026 14:21 by Etced 1 2	Replies:12 Views:1369	Etced Last Post by Etced 10 Jul 2026 14:21
Press Brake CNC control - possible? Category: General LinuxCNC Questions Topic started 28 Jun 2026 22:47, by Brad91 Last Post 10 Jul 2026 10:16 by andypugh	Replies:6 Views:593	Last Post by andypugh 10 Jul 2026 10:16
Index homing Mesa 7i96s Category: PnCConf Wizard Topic started 07 Jan 2023 23:25, by routerman22 Last Post 10 Jul 2026 02:46 by GeckoWorks 1 2 3 ... 6	Replies:59 Views:13.6k	GeckoWorks Last Post by GeckoWorks 10 Jul 2026 02:46
I CNC'ed my table to move a camera. Category: Show Your Stuff Topic started 09 Jul 2026 02:04, by tommylight Last Post 10 Jul 2026 02:23 by rodw	Replies:2 Views:418	Last Post by rodw 10 Jul 2026 02:23