PnCConf Wizard 663 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
emco compact 5 Topic started 01 Aug 2022 09:47, by carpa1970 Last Post 02 Oct 2022 10:03 by RotarySMP	Replies:7 Views:1944	Last Post by RotarySMP 02 Oct 2022 10:03
Connecting VFD to Rs-422 on mesa7i76e Topic started 27 Sep 2022 13:54, by webutt Last Post 29 Sep 2022 16:09 by flawapawacrew	Replies:2 Views:1509	flawapawacrew Last Post by flawapawacrew 29 Sep 2022 16:09
Can’t configure board ip in pncconf Topic started 18 Sep 2022 00:08, by joshuahuman Last Post 18 Sep 2022 01:53 by joshuahuman	Replies:9 Views:1231	joshuahuman Last Post by joshuahuman 18 Sep 2022 01:53
7i96s why this, what next? Topic started 16 Sep 2022 18:45, by Masiwood123 Last Post 17 Sep 2022 09:21 by Masiwood123	Replies:7 Views:1788	Last Post by Masiwood123 17 Sep 2022 09:21
7i77D single ended encoder connections Topic started 15 Sep 2022 05:30, by msrdiesel Last Post 16 Sep 2022 02:19 by msrdiesel	Replies:3 Views:1066	Last Post by msrdiesel 16 Sep 2022 02:19
Re:5i20 + 7i52s + 7i37TA -> change the IO Pins Topic started 06 Sep 2012 20:40, by trilobyte Last Post 15 Sep 2022 13:04 by BeWerk 1 2 3 ... 5	Replies:44 Views:29.7k	BeWerk Last Post by BeWerk 15 Sep 2022 13:04
HowTo: MESA Ethernet Board Network Config Using systemd Topic started 13 Sep 2022 13:56, by fletch Last Post 13 Sep 2022 16:05 by tommylight	Replies:3 Views:1407	Last Post by tommylight 13 Sep 2022 16:05
After switch to Mesa 6i25 (5i25), home switches not recognized. [Mis-configured] Topic started 11 Sep 2022 20:27, by clunc Last Post 13 Sep 2022 02:28 by clunc	Replies:8 Views:1393	Last Post by clunc 13 Sep 2022 02:28
How do PnCConf's Mesa Card 0 I/O tabs' pin numbers correspond to stepconf's? Topic started 28 Jul 2022 14:09, by clunc Last Post 06 Sep 2022 10:14 by clunc 1 2	Replies:15 Views:4570	Last Post by clunc 06 Sep 2022 10:14
7i96s: can't seem to get a stepper enable signal Topic started 03 Sep 2022 17:21, by Dr. John Last Post 04 Sep 2022 01:51 by PCW 1 2	Replies:14 Views:3703	Last Post by PCW 04 Sep 2022 01:51
[YES]Is there a way to create/generate firmware .xml from an existing .pin file? Topic started 22 Jul 2022 08:10, by clunc Last Post 30 Aug 2022 18:17 by Andreas_Rackow	Replies:8 Views:1956	Andreas_Rackow Last Post by Andreas_Rackow 30 Aug 2022 18:17
Ini file is overwritten Topic started 22 Aug 2022 16:45, by vkhargwanshi Last Post 23 Aug 2022 11:22 by JT	Replies:3 Views:1227	Last Post by JT 23 Aug 2022 11:22
Stepgen spindle Topic started 13 Aug 2022 12:21, by gilesclement Last Post 18 Aug 2022 13:52 by PCW	Replies:8 Views:1871	Last Post by PCW 18 Aug 2022 13:52
Cycle start/resume pause and external buttons problem (Mesa 7i76e card) Topic started 01 Aug 2022 08:06, by raychar Last Post 04 Aug 2022 15:03 by raychar 1 2	Replies:13 Views:3291	raychar Last Post by raychar 04 Aug 2022 15:03
All GPIO pins not shown by PnCConf for 7i96s Topic started 26 Jul 2022 09:08, by vkhargwanshi Last Post 03 Aug 2022 02:04 by vkhargwanshi 1 2	Replies:17 Views:4654	vkhargwanshi Last Post by vkhargwanshi 03 Aug 2022 02:04
Re: the sticky: "5i25 firmware XML files for pncconf" (missing newer files) Topic started 22 Jul 2022 08:02, by clunc Last Post 23 Jul 2022 01:29 by cmorley	Replies:1 Views:1188	cmorley Last Post by cmorley 23 Jul 2022 01:29
ISE Project Navigator 14.7 Topic started 21 Jul 2022 08:34, by Manja Last Post 21 Jul 2022 14:12 by PCW	Replies:1 Views:1193	Last Post by PCW 21 Jul 2022 14:12
My first steps with LinuxCNC - comments appreciated :) Using Mesa 7i80 and 7i78 Topic started 13 Jul 2022 22:27, by sukandar Last Post 21 Jul 2022 03:49 by PCW 1 2	Replies:13 Views:3429	Last Post by PCW 21 Jul 2022 03:49
PncConfig Errno 13 during setup Topic started 11 Jul 2022 14:21, by gilesclement Last Post 11 Jul 2022 17:19 by tommylight	Replies:2 Views:1000	Last Post by tommylight 11 Jul 2022 17:19
Error running LinuxCNC after setting up with Pncconf Topic started 09 Jul 2022 16:19, by mloser Last Post 09 Jul 2022 16:25 by tommylight	Replies:1 Views:987	Last Post by tommylight 09 Jul 2022 16:25

Time to create page: 0.255 seconds