PnCConf Wizard 874 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
Problems whit the switches in pncconf Topic started 04 Feb 2022 11:35, by Nest Last Post 10 Feb 2022 21:43 by Nest 1 2 3	Replies:23 Views:4592	Last Post by Nest 10 Feb 2022 21:43
PID info Topic started 06 Feb 2022 20:53, by Kylizer Last Post 06 Feb 2022 22:33 by PCW	Replies:1 Views:1150	Last Post by PCW 06 Feb 2022 22:33
Cannot get stepper motors to move Topic started 02 Feb 2022 01:12, by Jalapeno56 Last Post 06 Feb 2022 15:32 by Jalapeno56 1 2 3	Replies:25 Views:5286	Jalapeno56 Last Post by Jalapeno56 06 Feb 2022 15:32
PID Topic started 05 Jan 2022 16:49, by Bahaa_Asem Last Post 05 Feb 2022 01:54 by Todd Zuercher 1 2	Replies:13 Views:4051	Last Post by Todd Zuercher 05 Feb 2022 01:54
Mesa 7i96 ETH + Mesa 7i80 ETH Topic started 26 Jan 2022 04:50, by F0R3WER Last Post 28 Jan 2022 17:53 by PCW 1 2	Replies:11 Views:3833	Last Post by PCW 28 Jan 2022 17:53
config 6i25 & 7i77 - can't select pwm output Topic started 21 Jan 2022 07:17, by jpevner Last Post 22 Jan 2022 01:16 by jpevner 1 2	Replies:12 Views:2453	jpevner Last Post by jpevner 22 Jan 2022 01:16
Segmentation Fault Topic started 12 Jan 2022 00:56, by FlashPackets Last Post 13 Jan 2022 03:42 by FlashPackets	Replies:4 Views:1260	FlashPackets Last Post by FlashPackets 13 Jan 2022 03:42
Whats wrong with my .xml file? Topic started 25 Dec 2021 15:16, by Andreas_Rackow Last Post 05 Jan 2022 20:13 by Andreas_Rackow	Replies:5 Views:941	Andreas_Rackow Last Post by Andreas_Rackow 05 Jan 2022 20:13
7i76e configuration not working Topic started 03 Jan 2022 09:53, by jeremy Last Post 03 Jan 2022 10:20 by jeremy	Replies:2 Views:929	jeremy Last Post by jeremy 03 Jan 2022 10:20
Can pncconf be used to setup a mesa 7i76E in mode 2? Topic started 01 Jan 2022 20:20, by PhilCNC Last Post 01 Jan 2022 20:48 by PhilCNC	Replies:2 Views:955	Last Post by PhilCNC 01 Jan 2022 20:48
6i25 - 7i76/7i74 Pncconf and general questions Topic started 30 Dec 2021 11:07, by EGR Last Post 31 Dec 2021 11:03 by EGR	Replies:3 Views:1290	Last Post by EGR 31 Dec 2021 11:03
LinuxCNC terminates at startup after adding input pins with pnCConf for mesa7i76 Topic started 29 Dec 2021 12:09, by pCNC Last Post 29 Dec 2021 15:28 by pCNC	Replies:5 Views:1023	pCNC Last Post by pCNC 29 Dec 2021 15:28
Dual motors aren't stepping in sync Topic started 28 Dec 2021 20:11, by AgentWD40 Last Post 29 Dec 2021 14:02 by cmorley	Replies:7 Views:1045	cmorley Last Post by cmorley 29 Dec 2021 14:02
5i25+7i76 to 7i76E config conversion Topic started 22 Dec 2021 19:36, by eman5oh Last Post 26 Dec 2021 15:22 by eman5oh	Replies:9 Views:1378	eman5oh Last Post by eman5oh 26 Dec 2021 15:22
Dumb question - starting PnCConf with Lcnc RIP Topic started 22 Dec 2021 17:39, by spumco Last Post 23 Dec 2021 01:13 by spumco	Replies:2 Views:933	spumco Last Post by spumco 23 Dec 2021 01:13
Mesa 7i92 with 7i77 . No PWM after flashing bit file Topic started 09 Dec 2021 19:54, by DeRooij TSC Last Post 11 Dec 2021 08:28 by DeRooij TSC 1 2	Replies:10 Views:2931	DeRooij TSC Last Post by DeRooij TSC 11 Dec 2021 08:28
help please ,, problems configuring PnCConf Topic started 30 Nov 2021 23:10, by Servimet Last Post 02 Dec 2021 01:28 by Servimet	Replies:9 Views:1358	Last Post by Servimet 02 Dec 2021 01:28
5i24 Not showing in drop down for board selection Topic started 09 Sep 2017 16:53, by rickjmain Last Post 28 Nov 2021 17:06 by PCW	Replies:4 Views:1817	Last Post by PCW 28 Nov 2021 17:06
Pncconf qtplasmac Topic started 19 Nov 2021 15:05, by paulsao Last Post 28 Nov 2021 01:08 by MARCOS ROGERIO 1 2	Replies:14 Views:3121	MARCOS ROGERIO Last Post by MARCOS ROGERIO 28 Nov 2021 01:08
Mapping of pins on 7c81 P1, P2, and P7 to GPIO numbers Topic started 19 Nov 2021 22:43, by foxkid Last Post 19 Nov 2021 23:19 by PCW	Replies:1 Views:1183	Last Post by PCW 19 Nov 2021 23:19

Time to create page: 0.175 seconds