PnCConf Wizard 874 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
hm2_pci.ko issue Topic started 09 Apr 2018 17:44, by TRAUPMANN00 Last Post 10 Apr 2018 13:24 by PCW	Replies:4 Views:1413	Last Post by PCW 10 Apr 2018 13:24
Greenie problems configuring 6i25 with 7i77, using Granite Devices VSD-E drives Topic started 18 Feb 2018 21:38, by DeckelHead Last Post 06 Apr 2018 21:45 by DeckelHead 1 2 3 ... 8	Replies:73 Views:9995	DeckelHead Last Post by DeckelHead 06 Apr 2018 21:45
2 steppers on one axis 5i25 - 7i76 Topic started 20 Feb 2018 02:49, by chadrat6458 Last Post 05 Apr 2018 21:05 by TRAUPMANN00 1 2 3 ... 6	Replies:53 Views:10.3k	Last Post by TRAUPMANN00 05 Apr 2018 21:05
Setting up 5i25+7i85+8i20 Topic started 17 Nov 2013 03:34, by stes Last Post 04 Apr 2018 04:43 by blazini36 1 2 3 4	Replies:32 Views:9206	blazini36 Last Post by blazini36 04 Apr 2018 04:43
PNCConf Won't Start After Upgrade Topic started 25 Mar 2018 00:10, by DanMN Last Post 25 Mar 2018 21:35 by cmorley	Replies:1 Views:1224	cmorley Last Post by cmorley 25 Mar 2018 21:35
Can't configure Mesa 7i92 Topic started 27 Sep 2015 18:32, by dannym Last Post 08 Mar 2018 08:19 by aleksamc 1 2 3 4	Replies:32 Views:18.3k	Last Post by aleksamc 08 Mar 2018 08:19
5i25 with a Chinese parallel port BOB Topic started 01 Mar 2018 17:12, by Desertboy Last Post 05 Mar 2018 23:18 by andypugh	Replies:3 Views:2776	Last Post by andypugh 05 Mar 2018 23:18
Step/dir outputs for a stepper motor from a mesa 5i25 Topic started 10 Feb 2018 17:35, by Jakemestre1 Last Post 26 Feb 2018 21:00 by andypugh	Replies:6 Views:2251	Last Post by andypugh 26 Feb 2018 21:00
5i25 configuration with only a G540, no daughterboards Topic started 10 Jan 2018 00:03, by mpicco Last Post 23 Feb 2018 20:14 by mac44mag 1 2 3	Replies:25 Views:5966	mac44mag Last Post by mac44mag 23 Feb 2018 20:14
5i25 pulse voltage 1V Topic started 20 Feb 2018 19:59, by Lui23 Last Post 21 Feb 2018 16:56 by Lui23	Replies:2 Views:1238	Lui23 Last Post by Lui23 21 Feb 2018 16:56
Setup network interface Topic started 12 Feb 2018 12:17, by smplc Last Post 13 Feb 2018 15:15 by PCW	Replies:3 Views:4291	Last Post by PCW 13 Feb 2018 15:15
spindle speed pulse input 7i77 Topic started 12 Feb 2018 10:10, by Larsen2000 Last Post 12 Feb 2018 16:42 by Larsen2000	Replies:3 Views:2276	Last Post by Larsen2000 12 Feb 2018 16:42
5i25 + 7i77 Joint 0 Following Error PID Tuning Help needed Topic started 02 Feb 2018 02:36, by eighthaxis Last Post 09 Feb 2018 16:23 by eighthaxis	Replies:6 Views:2063	eighthaxis Last Post by eighthaxis 09 Feb 2018 16:23
6i24-16 + 7i52S + 7i37 Topic started 11 Dec 2017 10:52, by kohli-vie Last Post 28 Jan 2018 19:24 by lamandesigns	Replies:5 Views:1534	Last Post by lamandesigns 28 Jan 2018 19:24
Linear Encoder Position Feedback 6i25 - How To Set Up and Connect in LInux?! Topic started 15 Jan 2018 13:27, by Chriscore Last Post 16 Jan 2018 06:02 by Chriscore	Replies:4 Views:2777	Chriscore Last Post by Chriscore 16 Jan 2018 06:02
6i25Mesa did not connect to 7i76 Topic started 05 Jan 2018 10:51, by Chriscore Last Post 15 Jan 2018 17:50 by PCW	Replies:3 Views:2034	Last Post by PCW 15 Jan 2018 17:50
PNCconf does not start Topic started 10 Jan 2018 14:15, by kibo Last Post 12 Jan 2018 19:39 by bluephoenix	Replies:6 Views:1237	bluephoenix Last Post by bluephoenix 12 Jan 2018 19:39
PnCConf Backlash and STEPGEN_MAXVEL and STEPGEN_MAXACCEL Topic started 10 Jan 2018 04:41, by larry_no11 Last Post 10 Jan 2018 15:10 by cmorley	Replies:2 Views:1474	cmorley Last Post by cmorley 10 Jan 2018 15:10
PnCConf Mesa 7i76e pin mapping Topic started 08 Jan 2018 19:21, by larry_no11 Last Post 09 Jan 2018 01:58 by larry_no11	Replies:9 Views:4620	larry_no11 Last Post by larry_no11 09 Jan 2018 01:58
Test travel comes up short. I'm stumped Topic started 06 Jan 2018 02:13, by JohnnyCNC Last Post 06 Jan 2018 03:16 by JohnnyCNC	Replies:2 Views:1256	Last Post by JohnnyCNC 06 Jan 2018 03:16

Time to create page: 0.136 seconds