PnCConf Wizard 852 topics

Point n Click Configuration tool for Mesa Cards

Subject	Replies / Views	Last Post
Test/Tune Axis in pncconf Topic started 27 Aug 2011 21:41, by fgauder Last Post 31 Aug 2011 05:43 by cmorley 1 2	Replies:13 Views:14.2k	cmorley Last Post by cmorley 31 Aug 2011 05:43
Backlash Problems Topic started 19 Aug 2011 06:28, by efinkg Last Post 19 Aug 2011 17:45 by PCW	Replies:3 Views:4375	Last Post by PCW 19 Aug 2011 17:45
question re. estop logic - (pncconf output) Topic started 30 Jul 2011 03:09, by 1:1 Last Post 02 Aug 2011 13:48 by doug6949 1 2 3 4	Replies:32 Views:24k	doug6949 Last Post by doug6949 02 Aug 2011 13:48
Q re. motion. function (output from pncconf) Topic started 30 Jul 2011 03:25, by 1:1 Last Post 31 Jul 2011 07:22 by cmorley 1 2	Replies:17 Views:12.2k	cmorley Last Post by cmorley 31 Jul 2011 07:22
Problem in limit + home pin setup pncconf 2.4.7 Topic started 30 Jul 2011 17:02, by acondit Last Post 30 Jul 2011 21:26 by cmorley	Replies:2 Views:3845	cmorley Last Post by cmorley 30 Jul 2011 21:26
3 x questions re. spindle speed settings & outputs Topic started 30 Jul 2011 01:47, by 1:1 Last Post 30 Jul 2011 11:34 by cncbasher	Replies:3 Views:3294	cncbasher Last Post by cncbasher 30 Jul 2011 11:34
Would like to learn about index enable hoohah Topic started 29 Jul 2011 09:52, by 1:1 Last Post 30 Jul 2011 02:33 by PCW	Replies:3 Views:5374	Last Post by PCW 30 Jul 2011 02:33
help understanding the difference ... Topic started 26 Jul 2011 09:41, by 1:1 Last Post 29 Jul 2011 13:54 by BigJohnT 1 2 3 4	Replies:37 Views:25.3k	Last Post by BigJohnT 29 Jul 2011 13:54
request for pic or drawing for pncconf help page Topic started 21 Jul 2011 06:11, by cmorley Last Post 25 Jul 2011 11:37 by BigJohnT 1 2	Replies:12 Views:12.8k	Last Post by BigJohnT 25 Jul 2011 11:37
finalizing my control hardware - Double check me? Topic started 21 Jul 2011 18:11, by photomankc Last Post 22 Jul 2011 21:06 by Mike_Eitel	Replies:8 Views:7788	Last Post by Mike_Eitel 22 Jul 2011 21:06
autoconfig of pncconf from the pin or IDROM Topic started 06 Jul 2011 09:25, by cncbasher Last Post 09 Jul 2011 01:09 by cmorley 1 2	Replies:10 Views:10.6k	cmorley Last Post by cmorley 09 Jul 2011 01:09
Pin Order for I/O - can I change this ? Topic started 04 Jul 2011 11:39, by 1:1 Last Post 05 Jul 2011 08:54 by andypugh	Replies:8 Views:9327	Last Post by andypugh 05 Jul 2011 08:54
pncconf error configureing spindile Topic started 22 Jun 2011 09:45, by Nick Last Post 24 Jun 2011 07:23 by cmorley	Replies:3 Views:3636	cmorley Last Post by cmorley 24 Jun 2011 07:23
7i43 stepgen 4 axes Topic started 14 May 2011 09:25, by billykid Last Post 15 May 2011 19:45 by billykid 1 2	Replies:12 Views:13.5k	Last Post by billykid 15 May 2011 19:45
pncconf mesa i/o tabs Topic started 08 May 2011 21:08, by fabworx Last Post 09 May 2011 17:15 by fabworx	Replies:8 Views:9824	fabworx Last Post by fabworx 09 May 2011 17:15
7i48 firmware Topic started 18 Apr 2011 21:24, by fabworx Last Post 20 Apr 2011 01:07 by fabworx	Replies:4 Views:4089	fabworx Last Post by fabworx 20 Apr 2011 01:07
pncconf error 7i48 during configuration Topic started 18 Apr 2011 23:17, by fabworx Last Post 19 Apr 2011 15:11 by fabworx	Replies:3 Views:3410	fabworx Last Post by fabworx 19 Apr 2011 15:11
developing a stepper with encoder config Topic started 02 Apr 2011 03:53, by cmorley Last Post 13 Apr 2011 08:28 by cmorley 1 2	Replies:10 Views:13.1k	cmorley Last Post by cmorley 13 Apr 2011 08:28
stepgen by pncconf Topic started 27 Mar 2011 22:28, by andradela Last Post 02 Apr 2011 07:35 by andradela 1 2	Replies:16 Views:12.9k	andradela Last Post by andradela 02 Apr 2011 07:35
Change the stepgen outputs pins in 7i43 Topic started 03 Feb 2011 23:07, by andradela Last Post 06 Feb 2011 18:30 by billykid 1 2	Replies:14 Views:14.2k	Last Post by billykid 06 Feb 2011 18:30

Time to create page: 0.164 seconds