General LinuxCNC Questions 6166 topics

Questions about LinuxCNC

Subject	Replies / Views	Last Post
Can I position an axis using the numeric keypad? Topic started 05 May 2020 04:42, by pmconsulting Last Post 06 May 2020 06:01 by cmorley	Replies:3 Views:1288	cmorley Last Post by cmorley 06 May 2020 06:01
2.8.0~pre1 python linuxcnc.home(0) not working Topic started 02 May 2020 16:26, by LearningLinuxCNC Last Post 05 May 2020 16:37 by LearningLinuxCNC	Replies:5 Views:1641	Last Post by LearningLinuxCNC 05 May 2020 16:37
Mesa 5i25 supply voltages Topic started 22 Apr 2020 16:46, by Wirewrap Last Post 04 May 2020 19:00 by Wirewrap	Replies:2 Views:1112	Last Post by Wirewrap 04 May 2020 19:00
XHC WHB04B-4 pendant Topic started 01 May 2020 16:57, by Catch22 Last Post 02 May 2020 11:15 by rodw	Replies:2 Views:1262	Last Post by rodw 02 May 2020 11:15
how configure EMC2 in raspberry pi (GPIO ) Topic started 25 Jun 2014 23:34, by Anis Last Post 02 May 2020 08:34 by bbsr_5a	Replies:4 Views:5483	bbsr_5a Last Post by bbsr_5a 02 May 2020 08:34
Program takes roughly three times longer to run than it should Topic started 29 Apr 2020 23:05, by adouglas89 Last Post 01 May 2020 15:11 by bbsr_5a	Replies:8 Views:1512	bbsr_5a Last Post by bbsr_5a 01 May 2020 15:11
Version 2.8 or 2.9? Topic started 01 May 2020 14:04, by Catch22 Last Post 01 May 2020 15:08 by bbsr_5a	Replies:2 Views:1314	bbsr_5a Last Post by bbsr_5a 01 May 2020 15:08
proma sd step/dir Topic started 30 Apr 2020 20:36, by getyers Last Post 30 Apr 2020 21:07 by rodw	Replies:2 Views:930	Last Post by rodw 30 Apr 2020 21:07
SOLVED: Trouble getting at the tool table via Python... Topic started 29 Apr 2020 18:40, by pferrick Last Post 30 Apr 2020 05:56 by cmorley	Replies:5 Views:1513	cmorley Last Post by cmorley 30 Apr 2020 05:56
z-Clamp setup Topic started 29 Apr 2020 07:10, by bbsr_5a Last Post 29 Apr 2020 18:59 by bbsr_5a	Replies:3 Views:982	bbsr_5a Last Post by bbsr_5a 29 Apr 2020 18:59
Old setup from the ye good olde EMC2-days. Topic started 28 Apr 2020 19:05, by oddname Last Post 28 Apr 2020 19:35 by tommylight	Replies:1 Views:948	Last Post by tommylight 28 Apr 2020 19:35
Limit Switch Troubles - HAL Debounce Topic started 18 Dec 2014 10:43, by ctrl-frq Last Post 28 Apr 2020 18:45 by andypugh 1 2 3 ... 5	Replies:42 Views:17.7k	Last Post by andypugh 28 Apr 2020 18:45
Error al intentar modificar archivos Topic started 26 Apr 2020 19:12, by grojas21 Last Post 28 Apr 2020 08:58 by tommylight	Replies:4 Views:1100	Last Post by tommylight 28 Apr 2020 08:58
Stepper Drive Timing - CW-Motor Digital stepper driver CWD556 Topic started 06 Apr 2020 03:32, by blackmennewstyle Last Post 27 Apr 2020 12:14 by blackmennewstyle	Replies:4 Views:2257	Last Post by blackmennewstyle 27 Apr 2020 12:14
how to invert axes ? Topic started 06 Apr 2020 13:19, by alexandrub Last Post 27 Apr 2020 12:05 by tommylight 1 2	Replies:14 Views:3907	Last Post by tommylight 27 Apr 2020 12:05
Linuxcnc 2.9 jogging velocity fluctuations. Topic started 25 Apr 2020 21:15, by tommylight Last Post 27 Apr 2020 10:40 by tommylight 1 2	Replies:12 Views:6855	Last Post by tommylight 27 Apr 2020 10:40
Linuxcnc controling TinyG (Alterative to Chilipeppr) Topic started 27 Apr 2020 03:40, by ynneb Last Post 27 Apr 2020 05:34 by phillc54	Replies:1 Views:1649	Last Post by phillc54 27 Apr 2020 05:34
Simple GUI layout editor Topic started 27 Apr 2020 03:36, by ynneb Last Post 27 Apr 2020 05:31 by phillc54	Replies:1 Views:1273	Last Post by phillc54 27 Apr 2020 05:31
Lathe - tool offset in Y does not work Topic started 25 Apr 2020 18:53, by yaqwsx Last Post 26 Apr 2020 09:33 by yaqwsx	Replies:9 Views:1764	yaqwsx Last Post by yaqwsx 26 Apr 2020 09:33
Need help with unexpected/random stops on basic Parport/5 axis BOB setup Topic started 14 Mar 2020 14:08, by Lezard Last Post 25 Apr 2020 14:59 by Lezard 1 2 3	Replies:29 Views:3568	Lezard Last Post by Lezard 25 Apr 2020 14:59

Time to create page: 0.515 seconds