Plasmac 735 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Homing Issue "home switch inactive before backoff" Topic started 16 Jun 2022 07:08, by little_sparky Last Post 24 Jun 2022 16:24 by PCW	Replies:9 Views:1945	Last Post by PCW 24 Jun 2022 16:24
Is it possible to disable ARC_OK and still have THC UP/DOWN working? Topic started 23 Jun 2022 13:36, by fernandosf Last Post 23 Jun 2022 17:58 by fernandosf	Replies:5 Views:995	Last Post by fernandosf 23 Jun 2022 17:58
QTPlasmac interpreting Sheetcam material selection, M190 Topic started 23 Jun 2022 02:02, by LinfieldGarage Last Post 23 Jun 2022 12:29 by LinfieldGarage	Replies:4 Views:1238	LinfieldGarage Last Post by LinfieldGarage 23 Jun 2022 12:29
THCAD-10 Arc voltage not sensoring plate Topic started 31 May 2022 09:24, by aabtech Last Post 19 Jun 2022 13:30 by tommylight	Replies:1 Views:1281	Last Post by tommylight 19 Jun 2022 13:30
Latest post processor Topic started 17 Jun 2022 11:32, by bevins Last Post 18 Jun 2022 23:51 by phillc54	Replies:2 Views:1240	Last Post by phillc54 18 Jun 2022 23:51
Non-slip plate cutting Topic started 15 Jun 2022 12:42, by paulsao Last Post 16 Jun 2022 06:13 by Clive S	Replies:4 Views:976	Clive S Last Post by Clive S 16 Jun 2022 06:13
Ohmic probe a inssues water table Topic started 02 Apr 2022 19:15, by paulsao Last Post 14 Jun 2022 00:12 by Tsf62 1 2	Replies:10 Views:3589	Tsf62 Last Post by Tsf62 14 Jun 2022 00:12
WARNING FOR USERS THAT RUN BUSTER Topic started 04 Jun 2022 11:40, by phillc54 Last Post 10 Jun 2022 00:59 by tommylight	Replies:2 Views:1096	Last Post by tommylight 10 Jun 2022 00:59
Initial Height Skip (IHS) not functioning properly Topic started 24 May 2022 19:59, by Uthayne Last Post 08 Jun 2022 07:38 by phillc54 1 2	Replies:14 Views:2772	Last Post by phillc54 08 Jun 2022 07:38
How to configure THCAD-10 arc voltage Topic started 02 Jun 2022 06:37, by aabtech Last Post 05 Jun 2022 18:06 by aabtech	Replies:6 Views:1533	Last Post by aabtech 05 Jun 2022 18:06
Thanks for the QTPlasmaC Conversational Development Topic started 01 Jun 2022 19:45, by robertspark Last Post 01 Jun 2022 19:51 by snowgoer540	Replies:2 Views:1209	Last Post by snowgoer540 01 Jun 2022 19:51
Using one stepper Driver with two stepper motor Topic started 25 May 2022 09:24, by aabtech Last Post 30 May 2022 00:50 by andypugh	Replies:7 Views:1257	Last Post by andypugh 30 May 2022 00:50
Thcad ohmic probe1 Topic started 24 May 2022 10:51, by paulsao Last Post 24 May 2022 11:18 by paulsao	Replies:2 Views:786	Last Post by paulsao 24 May 2022 11:18
Mesa 7i92 board problem Topic started 30 Apr 2022 11:49, by aabtech Last Post 24 May 2022 03:56 by PCW	Replies:6 Views:1401	Last Post by PCW 24 May 2022 03:56
Mesa 7i92 to BOB all home switch Topic started 04 May 2022 13:27, by aabtech Last Post 23 May 2022 14:50 by aabtech	Replies:7 Views:1491	Last Post by aabtech 23 May 2022 14:50
Torch delay / torch height? Topic started 18 May 2022 21:39, by motal2004 Last Post 19 May 2022 23:34 by motal2004	Replies:5 Views:1180	motal2004 Last Post by motal2004 19 May 2022 23:34
THC cannot keep up Topic started 28 Apr 2022 19:58, by Jalapeno56 Last Post 17 May 2022 23:55 by Jalapeno56 1 2 3 ... 6	Replies:55 Views:7952	Jalapeno56 Last Post by Jalapeno56 17 May 2022 23:55
QtPlasmaC closes on startup after last update Topic started 15 May 2022 23:42, by CFE Last Post 16 May 2022 01:37 by CFE	Replies:4 Views:950	CFE Last Post by CFE 16 May 2022 01:37
valid arc lost final cut. Topic started 13 May 2022 13:23, by paulsao Last Post 13 May 2022 14:26 by snowgoer540	Replies:1 Views:933	Last Post by snowgoer540 13 May 2022 14:26
Scale axis Topic started 06 May 2022 14:54, by paulsao Last Post 11 May 2022 14:59 by paulsao 1 2	Replies:12 Views:5591	Last Post by paulsao 11 May 2022 14:59

Time to create page: 0.162 seconds