Plasmac 748 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Ohmic probe a inssues water table Topic started 02 Apr 2022 19:15, by paulsao Last Post 14 Jun 2022 00:12 by Tsf62 1 2	Replies:10 Views:4183	Tsf62 Last Post by Tsf62 14 Jun 2022 00:12
WARNING FOR USERS THAT RUN BUSTER Topic started 04 Jun 2022 11:40, by phillc54 Last Post 10 Jun 2022 00:59 by tommylight	Replies:2 Views:1221	Last Post by tommylight 10 Jun 2022 00:59
Initial Height Skip (IHS) not functioning properly Topic started 24 May 2022 19:59, by Uthayne Last Post 08 Jun 2022 07:38 by phillc54 1 2	Replies:14 Views:3255	Last Post by phillc54 08 Jun 2022 07:38
How to configure THCAD-10 arc voltage Topic started 02 Jun 2022 06:37, by aabtech Last Post 05 Jun 2022 18:06 by aabtech	Replies:6 Views:1870	Last Post by aabtech 05 Jun 2022 18:06
Thanks for the QTPlasmaC Conversational Development Topic started 01 Jun 2022 19:45, by robertspark Last Post 01 Jun 2022 19:51 by snowgoer540	Replies:2 Views:1417	Last Post by snowgoer540 01 Jun 2022 19:51
Using one stepper Driver with two stepper motor Topic started 25 May 2022 09:24, by aabtech Last Post 30 May 2022 00:50 by andypugh	Replies:7 Views:1584	Last Post by andypugh 30 May 2022 00:50
Thcad ohmic probe1 Topic started 24 May 2022 10:51, by paulsao Last Post 24 May 2022 11:18 by paulsao	Replies:2 Views:896	Last Post by paulsao 24 May 2022 11:18
Mesa 7i92 board problem Topic started 30 Apr 2022 11:49, by aabtech Last Post 24 May 2022 03:56 by PCW	Replies:6 Views:1605	Last Post by PCW 24 May 2022 03:56
Mesa 7i92 to BOB all home switch Topic started 04 May 2022 13:27, by aabtech Last Post 23 May 2022 14:50 by aabtech	Replies:7 Views:1840	Last Post by aabtech 23 May 2022 14:50
Torch delay / torch height? Topic started 18 May 2022 21:39, by motal2004 Last Post 19 May 2022 23:34 by motal2004	Replies:5 Views:1344	motal2004 Last Post by motal2004 19 May 2022 23:34
THC cannot keep up Topic started 28 Apr 2022 19:58, by Jalapeno56 Last Post 17 May 2022 23:55 by Jalapeno56 1 2 3 ... 6	Replies:55 Views:9207	Jalapeno56 Last Post by Jalapeno56 17 May 2022 23:55
QtPlasmaC closes on startup after last update Topic started 15 May 2022 23:42, by CFE Last Post 16 May 2022 01:37 by CFE	Replies:4 Views:1131	CFE Last Post by CFE 16 May 2022 01:37
valid arc lost final cut. Topic started 13 May 2022 13:23, by paulsao Last Post 13 May 2022 14:26 by snowgoer540	Replies:1 Views:1045	Last Post by snowgoer540 13 May 2022 14:26
Scale axis Topic started 06 May 2022 14:54, by paulsao Last Post 11 May 2022 14:59 by paulsao 1 2	Replies:12 Views:6376	Last Post by paulsao 11 May 2022 14:59
Temporary material lost when recovering with Run From Line Topic started 09 May 2022 05:58, by Daddio Last Post 11 May 2022 04:50 by Daddio	Replies:5 Views:1029	Daddio Last Post by Daddio 11 May 2022 04:50
Plasma+Oxy fuel machine/ PlasmaC/ Mesa card/THCAD/Parallel port query Topic started 09 May 2022 03:52, by rajsekhar Last Post 10 May 2022 22:54 by andypugh	Replies:3 Views:1239	Last Post by andypugh 10 May 2022 22:54
Pierce height would exceed Z axis maximum safe height condition found while... Topic started 27 Apr 2022 06:42, by Daddio Last Post 09 May 2022 04:58 by Daddio 1 2	Replies:10 Views:3659	Daddio Last Post by Daddio 09 May 2022 04:58
What does Temporary materials not created in a timely manner mean? Topic started 28 Jul 2021 05:23, by rodw Last Post 04 May 2022 19:57 by piramyd_head	Replies:3 Views:1252	piramyd_head Last Post by piramyd_head 04 May 2022 19:57
THC that controls z axis externally Topic started 30 Apr 2022 16:49, by Traza42 Last Post 02 May 2022 21:18 by Traza42 1 2	Replies:11 Views:2659	Traza42 Last Post by Traza42 02 May 2022 21:18
Float switch has disabled jogging Topic started 26 Apr 2022 17:40, by aabtech Last Post 26 Apr 2022 21:53 by snowgoer540	Replies:4 Views:1119	Last Post by snowgoer540 26 Apr 2022 21:53

Time to create page: 0.200 seconds