Plasmac 739 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
THCAD-300 and Hypertherm (65) Topic started 16 Feb 2020 21:48, by snowgoer540 Last Post 17 Feb 2020 23:49 by rodw 1 2 3	Replies:20 Views:4843	Last Post by rodw 17 Feb 2020 23:49
PlasmaC Topic started 27 Dec 2019 19:43, by CNC32 Last Post 12 Feb 2020 09:59 by tommylight 1 2 3	Replies:20 Views:6233	Last Post by tommylight 12 Feb 2020 09:59
PlasmaC Line Cut Video Topic started 11 Dec 2019 07:10, by thefabricator03 Last Post 06 Feb 2020 11:45 by tommylight 1 2	Replies:10 Views:3731	Last Post by tommylight 06 Feb 2020 11:45
Is it convenient using Plasmac without an Arc Voltage signal? (External THC) Topic started 30 Jan 2020 21:04, by GGG3 Last Post 05 Feb 2020 13:36 by GGG3	Replies:6 Views:1587	GGG3 Last Post by GGG3 05 Feb 2020 13:36
Questions re Plasmac Topic started 23 Jan 2020 14:34, by Clive S Last Post 23 Jan 2020 23:08 by phillc54	Replies:4 Views:1302	Last Post by phillc54 23 Jan 2020 23:08
New LinuxCNC Installation (Master Branch) "CANNOT FIND plasmac.hal" Topic started 10 Jan 2020 15:47, by GGG3 Last Post 22 Jan 2020 10:11 by Clive S	Replies:6 Views:2053	Clive S Last Post by Clive S 22 Jan 2020 10:11
Problems with updating to 2.9 on clean install Topic started 09 Jan 2020 06:09, by calvin.d Last Post 10 Jan 2020 05:27 by phillc54	Replies:8 Views:1820	Last Post by phillc54 10 Jan 2020 05:27
Configurator Error Topic started 20 Dec 2019 16:26, by AgentWD40 Last Post 08 Jan 2020 22:24 by andypugh 1 2	Replies:18 Views:3447	Last Post by andypugh 08 Jan 2020 22:24
Torch not turning off with m5 Topic started 08 Jan 2020 00:58, by CNC32 Last Post 08 Jan 2020 01:50 by phillc54	Replies:1 Views:1162	Last Post by phillc54 08 Jan 2020 01:50
Valid arc lost Topic started 06 Jan 2020 20:56, by CNC32 Last Post 07 Jan 2020 06:27 by tommylight	Replies:6 Views:1413	Last Post by tommylight 07 Jan 2020 06:27
Probe test problem Topic started 27 Sep 2019 16:56, by xunil Last Post 05 Jan 2020 01:42 by snowgoer540 1 2 3	Replies:23 Views:5888	Last Post by snowgoer540 05 Jan 2020 01:42
Cut Parameters Topic started 18 Sep 2019 09:07, by phillc54 Last Post 04 Jan 2020 06:34 by phillc54 1 2 3 4	Replies:39 Views:7396	Last Post by phillc54 04 Jan 2020 06:34
New to the forum questions Topic started 02 Jan 2020 19:51, by CBEAR Last Post 03 Jan 2020 20:24 by rodw	Replies:7 Views:1374	Last Post by rodw 03 Jan 2020 20:24
Gofab cns Topic started 01 Jan 2020 21:16, by Warrenh Last Post 02 Jan 2020 22:40 by phillc54	Replies:6 Views:1346	Last Post by phillc54 02 Jan 2020 22:40
THCAD-300 and Plasmac User Guide questions Topic started 31 Dec 2019 04:10, by snowgoer540 Last Post 02 Jan 2020 21:45 by chimeno 1 2	Replies:18 Views:3915	chimeno Last Post by chimeno 02 Jan 2020 21:45
Upgrade via Configurator Topic started 31 Dec 2019 23:33, by snowgoer540 Last Post 31 Dec 2019 23:38 by snowgoer540	Replies:2 Views:1344	Last Post by snowgoer540 31 Dec 2019 23:38
Cutting Sheet Artwork With PlasmaC Topic started 20 Dec 2019 13:21, by thefabricator03 Last Post 21 Dec 2019 00:29 by rodw	Replies:3 Views:1673	Last Post by rodw 21 Dec 2019 00:29
Float Switch Activated Program Paused Topic started 13 Dec 2019 23:15, by MakingStuff Last Post 14 Dec 2019 06:20 by phillc54 1 2	Replies:10 Views:3832	Last Post by phillc54 14 Dec 2019 06:20
How to update plasmaC Topic started 10 Oct 2019 12:23, by Clive S Last Post 09 Dec 2019 09:31 by Clive S 1 2	Replies:15 Views:4136	Clive S Last Post by Clive S 09 Dec 2019 09:31
THCAD-10 Mode Topic started 04 Dec 2019 13:51, by little_sparky Last Post 07 Dec 2019 07:09 by rodw	Replies:4 Views:1469	Last Post by rodw 07 Dec 2019 07:09

Time to create page: 0.168 seconds