Plasmac 743 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
cut quality question Topic started 03 Jul 2020 20:21, by motal2004 Last Post 03 Jul 2020 20:42 by tommylight	Replies:1 Views:1028	Last Post by tommylight 03 Jul 2020 20:42
Using Powermax with RS485 Topic started 24 Jun 2020 08:37, by Clive S Last Post 29 Jun 2020 23:30 by phillc54 1 2 3	Replies:29 Views:4383	Last Post by phillc54 29 Jun 2020 23:30
Mesa Hardware Recommendations Topic started 27 Jun 2020 19:25, by KaleD Last Post 28 Jun 2020 22:18 by KaleD 1 2	Replies:13 Views:3263	KaleD Last Post by KaleD 28 Jun 2020 22:18
7I96 Plasmac THAC / encoder config question Topic started 27 Jun 2020 21:53, by calvin.d Last Post 28 Jun 2020 00:43 by calvin.d 1 2	Replies:10 Views:3180	calvin.d Last Post by calvin.d 28 Jun 2020 00:43
THC input pins Topic started 27 Jun 2020 04:10, by KaleD Last Post 27 Jun 2020 05:06 by phillc54	Replies:1 Views:1170	Last Post by phillc54 27 Jun 2020 05:06
Raspberry Pi4 Hal configuration for torch on Topic started 24 Jun 2020 11:43, by greekart Last Post 26 Jun 2020 09:35 by greekart 1 2	Replies:11 Views:3547	Last Post by greekart 26 Jun 2020 09:35
THC not showing on screen Topic started 17 Jun 2020 23:35, by Nate Last Post 25 Jun 2020 11:46 by tommylight 1 2	Replies:14 Views:3367	Last Post by tommylight 25 Jun 2020 11:46
setting up thcad Topic started 29 May 2020 00:56, by Aaron3309 Last Post 25 Jun 2020 02:05 by PCW 1 2 3 4	Replies:36 Views:6670	Last Post by PCW 25 Jun 2020 02:05
I don't have an Arc OK Topic started 23 Jun 2020 03:41, by KaleD Last Post 24 Jun 2020 14:24 by KaleD 1 2	Replies:15 Views:4578	KaleD Last Post by KaleD 24 Jun 2020 14:24
Probe or Arc problem Topic started 24 Jun 2020 03:06, by KaleD Last Post 24 Jun 2020 04:43 by phillc54	Replies:1 Views:975	Last Post by phillc54 24 Jun 2020 04:43
PlasmaC questions new setup Topic started 22 May 2020 18:13, by Clive S Last Post 23 Jun 2020 07:24 by Clive S 1 2 3 ... 14	Replies:133 Views:18.6k	Clive S Last Post by Clive S 23 Jun 2020 07:24
Z axis height at end of cut Topic started 11 Jun 2020 21:35, by rodw Last Post 22 Jun 2020 20:48 by tommylight 1 2 3 ... 5	Replies:49 Views:8280	Last Post by tommylight 22 Jun 2020 20:48
Probe Z trouble Topic started 18 Jun 2020 04:41, by KaleD Last Post 20 Jun 2020 23:33 by phillc54	Replies:5 Views:1307	Last Post by phillc54 20 Jun 2020 23:33
plasmac install error Topic started 30 May 2020 00:09, by Nate Last Post 16 Jun 2020 12:07 by tommylight 1 2	Replies:16 Views:3788	Last Post by tommylight 16 Jun 2020 12:07
Feature update required. Topic started 13 Jun 2020 22:19, by rodw Last Post 16 Jun 2020 02:08 by phillc54 1 2 3	Replies:26 Views:4299	Last Post by phillc54 16 Jun 2020 02:08
Float Switch Activated Topic started 14 Jun 2020 12:21, by little_sparky Last Post 16 Jun 2020 01:53 by phillc54	Replies:6 Views:1321	Last Post by phillc54 16 Jun 2020 01:53
Watchdog has bit! Topic started 13 Jun 2020 04:28, by little_sparky Last Post 14 Jun 2020 12:48 by PCW 1 2	Replies:19 Views:4283	Last Post by PCW 14 Jun 2020 12:48
using Sheetcam and PlasmaC re Kerf Topic started 13 Jun 2020 17:56, by Clive S Last Post 14 Jun 2020 08:26 by phillc54 1 2	Replies:12 Views:3427	Last Post by phillc54 14 Jun 2020 08:26
Running CNC Plasma off generator Topic started 09 Jun 2020 07:42, by little_sparky Last Post 10 Jun 2020 12:14 by bbsr_5a 1 2	Replies:14 Views:3805	bbsr_5a Last Post by bbsr_5a 10 Jun 2020 12:14
THCAD-10 Jumper Settings Topic started 09 Jun 2020 07:35, by little_sparky Last Post 09 Jun 2020 07:43 by little_sparky	Replies:2 Views:1027	little_sparky Last Post by little_sparky 09 Jun 2020 07:43

Time to create page: 0.177 seconds