Plasmac 742 topics

A place to ask questions about the Plasmac interface

Subject	Replies / Views	Last Post
Cutting issue Topic started 19 Sep 2021 03:08, by UncleRemus Last Post 24 Sep 2021 18:02 by UncleRemus 1 2 3 4	Replies:34 Views:4390	UncleRemus Last Post by UncleRemus 24 Sep 2021 18:02
First test cut. No torch on when I run the program. Topic started 20 Sep 2021 21:31, by Shopro702 Last Post 22 Sep 2021 19:37 by Shopro702 1 2	Replies:16 Views:2535	Shopro702 Last Post by Shopro702 22 Sep 2021 19:37
Thc UP and Dn dont work Topic started 18 Sep 2021 15:32, by paulsao Last Post 19 Sep 2021 02:27 by phillc54	Replies:8 Views:1110	Last Post by phillc54 19 Sep 2021 02:27
Mode 2 - THC down limit Topic started 15 Sep 2021 19:55, by fernandosf Last Post 17 Sep 2021 18:24 by fernandosf	Replies:6 Views:912	Last Post by fernandosf 17 Sep 2021 18:24
QTPlasmaC mode2 - valid arc lost Topic started 07 Sep 2021 19:49, by fernandosf Last Post 17 Sep 2021 18:11 by fernandosf 1 2	Replies:19 Views:2879	Last Post by fernandosf 17 Sep 2021 18:11
THCAD-10 and voltaje divider ratio. Topic started 26 Aug 2021 22:52, by paulsao Last Post 12 Sep 2021 11:14 by rodw	Replies:8 Views:1718	Last Post by rodw 12 Sep 2021 11:14
Choosing a compressor for plasma cutting Topic started 09 Sep 2020 15:09, by tommylight Last Post 07 Sep 2021 19:56 by billykid 1 2	Replies:12 Views:7850	Last Post by billykid 07 Sep 2021 19:56
QtPlasmaC Jogging Lag Topic started 02 Sep 2021 16:32, by Uthayne Last Post 07 Sep 2021 13:20 by Uthayne 1 2 3 4	Replies:32 Views:4368	Uthayne Last Post by Uthayne 07 Sep 2021 13:20
PlasmaC Will Not Activate Torch Pin on My 7i96 Topic started 24 Sep 2019 02:47, by MakingStuff Last Post 05 Sep 2021 02:40 by pkasy 1 2 3	Replies:25 Views:4192	Last Post by pkasy 05 Sep 2021 02:40
QTvcp ERROR! Message # 1 Topic started 02 Sep 2021 07:38, by danilom Last Post 02 Sep 2021 07:50 by phillc54	Replies:1 Views:920	Last Post by phillc54 02 Sep 2021 07:50
Which THCAD to use for Plasma cutter without voltage divider Topic started 10 Jun 2021 20:55, by alchemy Last Post 31 Aug 2021 11:34 by tommylight 1 2	Replies:12 Views:3616	Last Post by tommylight 31 Aug 2021 11:34
wrong scale thc of the z axis during cutting on qtplasmac Topic started 06 Jul 2021 12:17, by sibista Last Post 27 Aug 2021 12:36 by sibista 1 2 3 ... 10	Replies:94 Views:12.2k	sibista Last Post by sibista 27 Aug 2021 12:36
QTPlasmaC, first cut ever. What to do after "initial setup"? Topic started 23 Aug 2021 19:21, by fernandosf Last Post 26 Aug 2021 23:03 by phillc54 1 2 3	Replies:20 Views:4680	Last Post by phillc54 26 Aug 2021 23:03
Fusión 360 and Plasmac Topic started 24 Aug 2021 22:08, by paulsao Last Post 25 Aug 2021 14:16 by paulsao	Replies:7 Views:1066	Last Post by paulsao 25 Aug 2021 14:16
IMPORTANT NOTICE for PlasmaC users Topic started 12 May 2021 00:38, by phillc54 Last Post 25 Aug 2021 04:33 by phillc54	Replies:1 Views:8791	Last Post by phillc54 25 Aug 2021 04:33
Showing G53 coordinates Topic started 20 Aug 2021 18:39, by fernandosf Last Post 23 Aug 2021 12:29 by beefy 1 2 3	Replies:21 Views:4136	beefy Last Post by beefy 23 Aug 2021 12:29
Ignore probe during cut Topic started 17 Aug 2021 15:46, by mariusl Last Post 18 Aug 2021 06:43 by mariusl	Replies:8 Views:1677	Last Post by mariusl 18 Aug 2021 06:43
PnCConf Wizard doesn't launch Topic started 09 Aug 2021 01:34, by CFE Last Post 15 Aug 2021 15:58 by crowloy 1 2	Replies:19 Views:2614	crowloy Last Post by crowloy 15 Aug 2021 15:58
QTPlasmaC Z axis "following error" (but it works in AXIS) Topic started 12 Aug 2021 12:28, by fernandosf Last Post 14 Aug 2021 20:36 by fernandosf	Replies:7 Views:1265	Last Post by fernandosf 14 Aug 2021 20:36
Camera For Touchoff Topic started 17 Sep 2020 05:46, by phillc54 Last Post 08 Aug 2021 08:47 by partec 1 2 3 ... 7	Replies:60 Views:14.5k	partec Last Post by partec 08 Aug 2021 08:47

Time to create page: 0.144 seconds